784912
9
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
Page 6
VERSASSAGE Jets - These jets may be adjusted to provide either a
stationary, direct stream or, by positioning the nozzle to one side or the
other, a rotating jet stream.
The VERSASSAGE jets allow you to regulate the force of the massage.
Rotate the fascia ring counter-clockwise to reduce the force, or
clockwise to increase the force. Notice that turning off the flow to some
jets increases the flow to the other jets. To avoid damage to your spa’s
plumbing and components, do not turn off more than half of these jets at
the same time. For cleaning instructions, see the VERSASSAGE Jets
Maintenance section.
ORBISSAGE Jets - This jet provides a unique, pulsating massage. The
flow is adjustable in that it can be turned completely off or on (by
rotating the jet faceplate). It is also interchangeable with the
VERSASSAGE jet. For cleaning or replacement instructions see
VERSASSAGE Jets in the Spa Care and Maintenance section.
DIVERTER VALVES
The diverter valves on your spa allow you to direct the flow of water
from the pumps to various combinations of jets. The functions of these
diverter valves can best be learned by experimentation as follows:
Set all air controls to the “ON” position.
Turn on both pumps.
Turn the handle on
each diverter valve and
see which groups of
jets are affected. (Note
that you can adjust the
diverter valves to any
position between the
two possible extremes to
achieve the jet pressure
that feels best to you.)
IMPORTANT: Your
spa is not designed to provide full power to all jets when the diverter
valves are in the “mid” position. However, with the diverter valve in this
position, you may increase the power to selected jets by rotating the
face of the ADAPTAFLO and ADAPTASSAGE jets to close the ones
that are not in use.
TIP: Turn both pumps on and place the diverter valves to the “Mid-
Position”. Then experiment with each of the air controls to see their
effect.
VERSASSAGE Jet
ORBISSAGE Jet
Getting Started
ACQUARELLA WATERFALL VALVE
Your spa is equipped with the ACQUARELLA
waterfall feature. It is activated by turning on Jet
Pump 2 (either low or high speed). The flow is
regulated by turning the waterfall valve on the
inside wall of the spa.
AIR CONTROLS
Each jet system has its own air control. These allow
you to change the power of the jets by regulating the
amount of air that is mixed with the water coming out
of the jets.
ATLAS NECK JET VALVE
The CALDERA spas are equipped with 4 directional neck jets located
in the EcstaSeat
. The flow of the neck jets is regulated by turning the
ATLAS NeckJet valve on the inside wall of the spa.
CALDERA LOGO LIGHT
The CALDERA logo on the front of the spa illuminates an orange and
gray color. These colors indicate the power and ready status of the spa
without having to open the cover to look at the control panel.
Orange Indicator: The ORANGE indicator will light when the spa
water temperature is within 1°C of the set temperature, and will turn
off when the temperature is outside of that range. If you increase or
decrease the temperature setting of the spa, the ready indicator will
turn off until the water temperature reaches the acceptable range for
the new temperature setting. A flashing ORANGE indicator means a
problem may exists with the temperature sensor (see Troubleshooting
section for more information).
Gray Indicator: The GRAY indicator is ‘on’ when the spa is properly
supplied with power. It also provides a diagnostic function–a flashing
GRAY indicator indicates that the heater high limit has tripped, meaning
that either the spa water is above its acceptable temperature range,
or a malfunction has occurred within the spa (such as low circulation
due to clogged filters). An ‘off GRAY indicator means that there is a
problem with the spa control box or the power supplied to the spa (see
Troubleshooting section for more information).
QUICK START-UP INSTRUCTIONS
BEFORE YOU FILL YOUR SPA
Make sure your spa has been properly installed per all local codes, this
includes the location of the spa, the foundation of the spa as well as
the electrical installation of the spa. Installation instructions in the form
of a Pre-Delivery Instruction booklet can be obtained from either your
CALDERA dealer or online.
DO:
Know which water treatment system you will be using and make sure
you have necessary chemicals available. Read all of the instructions
that come with the system.
Have FRESHWATER 5-way Test Strips Available.
Have pH/Alkalinity Up & Down available.
Know the calcium hardness of your water, contact your dealer to help
you with this information. See Water Quality and Maintenance for more
information.
IIMPORTANT: The spa can be filled with “softened” water as long as
the calcium hardness parameters (pg. 2) are maintained.
Purchase the Clean Screen
pre-filter to remove unwanted
contaminants from the tap water. This is recommended, not required.
DON'T:
Power up the spa until it has been filled with water! Power to the
spa automatically activates critical components within the spa, such
as controls, heater, circulation pump, and other systems. If power
is supplied to these components prior to the spa being filled, the
components will be damaged, and this may result in a non-warranty
component failure.
Fill the spa with hot water or cold water with cold water temperature
below 10ºC (50ºF)! Tripping of the high-limit thermostat may result
causing your spa to stop functioning.
START-UP
Your CALDERA spa has been thoroughly tested during the
manufacturing process to ensure reliability and long-term customer
satisfaction. A small amount of water may have remained in the
plumbing after testing and, as a result, may have spotted the spa shell
or the spa siding prior to delivery. Before filling the spa, wipe the spa
shell clean with a soft rag. The following instructions must be read and
followed exactly to ensure a successful start-up or refill.
CAUTIONS
DO NOT fill the spa with hot water, as tripping of the high-limit
thermostat may result.
DO NOT CONNECT POWER TO AN EMPTY SPA. Power to the
spa automatically activates critical components within the spa, such
as controls, heater, and other systems. If power is supplied to these
components prior to the spa being filled, the components will be
damaged, and this may result in a non-warranty component failure.
DO NOT use your spa after filling until all of the steps listed below are
completed.
DO NOT add chlorine if treating your spa with polyhexamethylene
biguanide (Biguanide, PHMB, eg. BAQUASPA) sanitizer.
Before filling your spa for the first time, remove the equipment
compartment door and check to ensure that the unions on either side
of the pump(s) and heater are hand-tight.
1. CLOSE DRAIN, remove the filter compartment cover, skimmer
basket, weir, and filter. Fill your spa through the filter compartment
using the CleanScreen pre-filter that attaches to your garden hose.
The water level of your spa should be maintained at a level 2.5 cm
above the highest jet in the shell of the spa. Reinstall the filter and
then the skimmer basket, and weir once the spa is filled.
Gray indicator - Power to spa is on
Orange indicator - water is ready, within 1°C of set temperature
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Caldera Utopia - serie 2019 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Caldera Utopia - serie 2019 in de taal/talen: Engels als bijlage per email.

De handleiding is 10.12 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Caldera Utopia - serie 2019

Caldera Utopia - serie 2019 Gebruiksaanwijzing - Nederlands - 44 pagina's

Caldera Utopia - serie 2019 Gebruiksaanwijzing - Deutsch - 44 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info