557409
44
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
10 Troubleshooting
Logano plus GB402 – 6 720 804 428 (2012/09)
44
10.2 Operating and fault displays
10.2.1 Operating messages
Display code Sub-code Cause Description
Test procedure/
cause
Correction
2P 564 Temperature rise at the
boiler sensor too rapid
( > 70 K/min).
Heat exchanger protection
due to excessively fast heat-
up speed.
No or insufficient heat
transfer (e.g.
thermostatic valves or
mixers closed).
Ensure adequate heat transfer.
Inadequate boiler flow
rate.
Install adequately sized pumps.
Pump does not work. Check whether the pump is
being switched. Replace the
pump if required.
Deposits on the water
side of the boiler (dirt
from the heating system,
scaling).
Flush/clean the boiler block on
the heating water side with
agents approved for use with
aluminium.
OA - Appliance in switching
optimisation prog.
A new burner demand occurs
within the set switching
optimisation time. Appliance
in cycle block. The standard
switching optimisation time is
10 min.
Check output setting at
the BC10 basic controller.
Match the boiler output to the
required heat demand of the
building.
Check the control setting
in the RC35 control unit.
Match the control setting to the
system conditions.
OH - The appliance is in
standby mode; there is no
heat demand.
The boiler is ready to operate;
there is no heat demand from
the heating circuit.
--
OY - The current boiler water
temperature is higher
than the set boiler water
temperature.
The current boiler water
temperature is higher than the
set boiler water temperature.
The boiler shuts down.
- -
OP - Waiting for the fan to
ramp up.
The ramp-up needs to be
detected for the sequence to
be able to proceed.
--
OE - The appliance is in
standby mode, there is an
active heat demand, but
an excess of energy is
being supplied.
The current system heat
demand is lower than that
which the minimum
modulation level of the burner
supplies.
- -
OU - Start of the program
sequence to start the
burner.
---
OC - Burner start begins. - - -
OL - Opening the gas train. - - -
OF - Insufficient boiler flow
rate.
Temperature differential
between the flow and return
>15K.
Temperature differential
between flow and safety
temperature sensor > 15K.
Check the flow
temperature on the
BC10,
check the return
temperature with RC35 or
the service key,
measure the resistance of
the boiler sensor (high
limit safety cut-out (STB))
and compare with the
curve.
Adjust the setting of the boiler
circuit pump.
Check the surface temperature
of the cast section that is
equipped with the safety
temperature sensor using a
thermometer.
Check whether a cast section is
blocked with dirt.
Tab. 21 Operating codes
44

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Buderus Logano plus GB402 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Buderus Logano plus GB402 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Buderus Logano plus GB402

Buderus Logano plus GB402 Installatiehandleiding - Nederlands - 60 pagina's

Buderus Logano plus GB402 Gebruiksaanwijzing - Nederlands - 16 pagina's

Buderus Logano plus GB402 Gebruiksaanwijzing - Deutsch - 2 pagina's

Buderus Logano plus GB402 Gebruiksaanwijzing - English - 20 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info