560475
88
Verklein
Vergroot
Pagina terug
1/100
Pagina verder
88
We reserve the right to make any changes due to technical modifications!
Installation and Servicing Instructions Logamax plus GB142-24/30/45/60 • Version 12/2004
Buderus Hydronic Systems • http://www.buderus.net
Appendix16
16.2 Error messages
z Press the "Service" button to display the service
code (e. g. "$").
z Press the "Service"
button to display the error
code (e. g. "").
The error message is a combination of the service code
(e. g. "$") and the error code (e. g. ""). You can only
resolve the error message using the Service chapter in
this manual.
INSTRUCTION FOR INSTALLERS
The display may also show system faults
(e. g. "$"). In principle, they are identified by
the initial letter "A" and they refer to faults
between the appliance and the additionally
available electronic components.
Display Meaning
Flame monitoring
$  No ionization message after ignition.
& 

Ionization measured before burner start.
/The flame went out during the heating phase.
3Hot-surface ignitor on for too long.
Grid voltage
&The grid power was interrupted after an error.
/

UBA fault.
External switching contact
< External switching contact, e. g. temperature
safety switch for floor heating, has taken place.
System faults
$Communication fault between UBA and KIM.
+


UBA fault.
3UBA fault.
/


Faulty gas burner fitting cable connection.
8KIM out of order.
< Communication fault between BC10 basic
controller and UBA.
( System faults
$&
)+/
<
Internal UBA fault.
Display Meaning
Water flow / water pressure
(System pressure too low < 3 psi (20 mbar).
)Temperature difference between safety and
supply sensors too much or no temperature
increase after starting the burner.
/Test of pump operation via a pressure increase
in the heating system (during pump start).
3 Temperature increase of safety sensor or supply
sensor too high.
8 Temperature difference between supply and
return sensor too much.
< Pump feedback fault.
Fan speed
$Fan unit failed during operation.
)Air volume flow not lost for 24 hours.
/Fan shut down during security test.
3Fan unit is running too slowly.
<Fan unit is running too fast.
Temperatures
$Supply sensor over 220 °F (105 °C).
(Sensor test failed
/  Safety sensor affected by short circuit or higher
than 266 °F (130 °C).
3  Loose contact or defective safety sensor.
8  Supply sensor affected by short circuit.
<  Loose contact or faulty supply sensor.
88

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Buderus Logamax plus GB142-60 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Buderus Logamax plus GB142-60 in de taal/talen: Engels als bijlage per email.

De handleiding is 4,63 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Buderus Logamax plus GB142-60

Buderus Logamax plus GB142-60 Gebruiksaanwijzing - Nederlands - 12 pagina's

Buderus Logamax plus GB142-60 Gebruiksaanwijzing - Deutsch - 16 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info