451231

Brother MFC-6890CDW Handleiding

1
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
1
Start Here
MFC-6890CDW
Quick Setup Guide
UK/IRE/GEN/SAF Version 0
Before you can use the machine, read this Quick Setup Guide for the correct setup and installation.
1
Unpack the machine and check the components
WARNING
Plastic bags are used in the packaging of your machine. To avoid danger of suffocation, please keep
these bags away from babies and children.
a Remove the protective tape and film covering the machine. Make sure you also remove the film covering
the Touchscreen.
b Make sure you have all components.
WARNING Warnings tell you what to do to prevent possible personal injury.
Important
DO NOT connect the USB cable yet (if you are using a USB
cable).
Ink Cartridges [x4]
Black (LC1100HY-BK)
Yellow (LC1100HY-Y)
Cyan (LC1100HY-C)
Magenta (LC1100HY-M)
Quick Setup Guide
User’s Guide CD-ROM Power Cord Telephone Line Cord
One Touch Labels
Note
• The components included in the box may differ depending on your country.
• Save all packing materials and the box in case for any reason you must ship your machine.
•
The interface cable is not a standard accessory. Buy the appropriate interface cable for the interface you
want to use (USB or Network).
USB cable
Please make sure you use a USB 2.0 cable (Type A/B) that is no more than 2 metres long.
Network cable
Use a straight-through Category5 (or greater) twisted-pair cable for 10BASE-T or 100BASE-TX Fast Ethernet Network.
2
2
Load plain A4 paper
a Pull paper tray#1 (the upper tray) a
completely out of the machine.
b Open the paper tray cover a.
c With both hands, gently press and slide the
paper side guides a and then the paper length
guide b to fit the paper size you are loading in
the tray.
Make sure that the triangular marks c on the
paper side guides a and paper length guide b
line up with the mark for the paper size you are
using.
d Fan the stack of paper well to avoid paper jams
and misfeeds.
e Gently put the paper into paper tray#1 print
side down and top edge first. Check that the
paper is flat in the tray.
f Gently adjust the paper side guides to the
paper with both hands. Make sure that the
paper side guides touch the edges of the
paper.
g Close the paper tray cover. Check that the
paper is flat in the tray and below the maximum
paper mark a.
1
1
3
3
2
1
Important
DO NOT push the paper in too far.
1
1
3
h Slowly push the paper tray completely into the
machine.
i While holding the paper tray in place, pull out
the paper support a until it clicks, and then
unfold the paper support flap b.
Note
For information about tray#2, see Loading paper
in paper tray #2 in Chapter 2 of the User’s Guide.
1
2
4
3
Connect the power cord
and telephone line
a Connect the power cord.
WARNING
The machine must be fitted with an earthed
plug.
b Connect the telephone line cord. Connect one
end of the telephone line cord to the socket on
the machine marked LINE and the other end to
a telephone wall socket.
WARNING
Since the machine is grounded through the
power outlet, you can protect yourself from
potentially hazardous electrical conditions on
the telephone network by keeping the power
cord connected to your machine when you
connect it to a telephone line. Similarly, you
can protect yourself when you want to move
your machine by disconnecting the telephone
line first and then the power cord.
Important
DO NOT connect the USB cable yet (if you are
using a USB cable).
Important
The telephone line cord MUST be connected
to the socket on the machine marked LINE.
Note
If you are sharing one telephone line with an
external telephone, connect it as shown below.
1 Extension telephone
2 External telephone
Note
If you are sharing one telephone line with an
external telephone answering machine, connect it
as shown below.
Set the receive mode to External TAD if
you have an external answering machine.
See Choose a Receive Mode on page 7.
For additional details, see Connecting an
external TAD (telephone answering device)
in Chapter 7 of the User’s Guide.
11
22
5
4
Install the ink cartridges
WARNING
If ink gets in your eyes, wash them out with
water at once, and if irritation occurs consult a
doctor.
a Make sure that the power is turned on.
The LCD shows:
b Open the ink cartridge cover a.
c Remove the green protective part a.
d Unpack the ink cartridge.
e Turn the green knob on the protective yellow
cap clockwise until it clicks to release the
vacuum seal, then remove the cap a.
f Take care to match the colour of the lever a
with the cartridge colour b, as shown in the
diagram below.
g Install each ink cartridge in the direction of the
arrow on the label.
Note
Do not throw away the green protective part.
You will need it if you transport the machine.
No Cartridge
Install Ink
Black
BK
Cyan
C
Yellow
Y
Magenta
M
1
1
1
1
1
2
6
h
Gently push the ink cartridge until it clicks. After
all the ink cartridges are installed close the ink
cartridge cover.
5
Check the print quality
a When the preparation process has finished, the
LCD shows this message
.
Press Colour Start.
b Check the quality of the four colour blocks a
on the sheet. (black/yellow/cyan/magenta)
c If all lines are clear and visible, press Yes to
finish the quality check.
If you can see missing short lines, press No and
go to d.
d The LCD asks you if the print quality is OK for
black and colour. Press Yes or No.
After pressing Yes or No for both black and
colour, the LCD shows:
e Press Colour Start, the machine will then start
cleaning the colours.
f After cleaning is finished, press Colour Start.
The machine starts printing the Print Quality
Check Sheet again. Go back to b.
Note
The machine will prepare the ink tube system for
printing. This process will take approximately four
minutes. Do not turn off the machine.
Important
Make sure you put paper in the upper tray for
the initial setup.
Y
C
B
K
Set Paper and Press Start
1
1
<Black> <Colour>
OK OK
<Black> <Colour>
Poor Poor
Black OK?
Yes No
Start Cleaning?
Press Start
7
6
Choose a Receive Mode
There are four possible receive modes: Fax Only,
Fax/Tel, Manual and External TAD.
a Press MENU.
b Press a or b to display Initial Setup.
c Press Initial Setup.
d Press Receive Mode.
e Press Fax Only, Fax/Tel, External TAD
or Manual.
f Press Stop/Exit.
7
Set the LCD contrast
(If needed)
If you are having difficulty reading the LCD, try
changing the contrast setting.
a Press MENU.
b Press a or b to display General Setup.
c Press General Setup.
d Press a or b to display LCD Settings.
e Press LCD Settings.
f Press LCD Contrast.
g Press Light, Med or Dark.
h Press Stop/Exit.
8
Set the date and time
The machine displays the date and time, and if you
set up the station ID, it will add it to each fax you send.
a Press MENU.
b Press a or b to display Initial Setup.
c Press Initial Setup.
d Press Date&Time.
e Enter the last two digits of the year on the
Touchscreen, and then press OK.
(e.g. Enter 0 9 for 2009.)
f Repeat for Month and Day, and Hours and
Minutes in 24-hour format.
g Press Stop/Exit.
For details, see Using receive modes in
Chapter 6 of the User's Guide.
Do you want to use the telephone features of your
machine (if available) or an external telephone or
external telephone answering device connected on the
same line as the machine?
Your machine
automatically answers
every call as a fax.
Your machine controls
the line and
automatically answers
every call. If the call is
not a fax, the telephone
will ring for you to pick
up the call.
Your external telephone
answering device (TAD)
automatically answers
every call. Voice
messages are stored
on the external TAD.
Fax messages are
printed.
You control the
telephone line and must
answer every call
yourself.
Do you want the machine to
answer fax and telephone calls
automatically?
Manual
Fax Only
Fax/Tel
External TAD
No
Yes
Yes
No
No
Yes
Are you using the voice message
function of an external telephone
answering device?
Note
You can also adjust the angle of the display by
lifting it.
Year:2009
Ye a r : 2 0 0 9
Date&Time
D a t e & Ti m e
8
9
Enter personal
information (station ID)
You should store your name and fax number to be
printed on all fax pages that you send.
a Press MENU.
b Press a or b to display Initial Setup.
c Press Initial Setup.
d Press Station ID.
e Enter your fax number (up to 20 digits) on the
Touchscreen, and then press OK. For example,
to enter the UK dialling code “+44”, press
until + appears then enter +. Press until
numbers appear then press 4, 4 and the rest of
your number.
f Enter your name (up to 20 characters) using
the Touchscreen, and then press OK.
g Press Stop/Exit.
10
Fax Transmission Report
Your Brother machine is equipped with a
Transmission Verification Report that can be used as
confirmation that you sent a fax. This report lists the
name or fax number of the receiving party, the date,
time, and duration of the transmission, the number of
pages transmitted, and whether or not the
transmission was successful. If you want to use the
Fax Transmission Report feature, see Printing
Reports in Chapter 9 of the User
’s Guide.
11
Set tone or pulse dialling
mode
Your machine comes set for Tone dialling service. If
you have Pulse dialling service (rotary), you need to
change the dialling mode.
a Press MENU.
b Press a or b to display Initial Setup.
c Press Initial Setup.
d Press a or b to display Tone/Pulse.
e Press Tone/Pulse.
f Press Pulse (or Tone).
g Press Stop/Exit.
12
Set the telephone line
type
If you are connecting the machine to a line that
features PBX or ISDN to send and receive faxes, it is
necessary to change the telephone line type
accordingly by completing the following steps.
a Press MENU.
b Press a or b to display Initial Setup.
c Press Initial Setup.
d Press a or b to display Phone Line Set.
e Press Phone Line Set.
f Press Normal, PBX or ISDN.
g Press Stop/Exit.
PBX and TRANSFER
The machine is initially set to Normal, which lets the
machine connect to a standard PSTN (Public
Switched Telephone Network) line. However, many
offices use a central telephone system or Private
Branch Exchange (PBX). Your machine can be
connected to most types of PBX. The machine’s
recall feature supports timed break recall only (TBR).
TBR will work with most PBX systems allowing you to
gain access to an outside line, or transfer calls to
another extension. The feature works when the R key
is pressed.
Note
• To enter numbers or special letters, press
repeatedly until the character you want to enter
appears in the character set.
• If you need to enter a character that is on the
same button as the last character, press c to
move the cursor to the right.
• If you entered a letter incorrectly and want to
change it, press d or c to move the cursor to the
incorrect character, press .
Note
If you make a mistake and want to start again,
press Stop/Exit and go back to a.
For details, see Entering Text in Appendix C
of the User's Guide.
9
Windows
®
Macintosh
®
Windows
®
Macintosh
®
USB Wired Network
Wireless Network
13
Choose your connection type
For USB interface cable
Windows
®
, go to page 10
Macintosh
®
, go to page 14
For Wired Network
Windows
®
, go to page 17
Macintosh
®
, go to page 22
For Wireless Network
Windows
®
and Macintosh
®
,
go to page 26
10
Windows
®
USB
For USB Interface Users
(For Windows
®
2000 Professional/XP/XP Professional x64 Edition/
Windows Vista
®
)
14
Before you install
a Make sure that your computer is ON and you
are logged on with Administrator rights.
b Disconnect the machine from the power socket
and from your computer, if you already
connected an interface cable.
15
Install MFL-Pro Suite
a Put the supplied CD-ROM into your CD-ROM
drive. If the model name screen appears,
choose your machine. If the language screen
appears, choose your language.
b The CD-ROM main menu will appear. Click
Initial Installation.
c Click Install MFL-Pro Suite.
Important
• DO NOT connect the USB cable yet.
• If there are any programs running, close
them.
• Make sure there are no memory cards or a
USB Flash memory drive inserted.
• The screens may differ depending on the
operating system.
• The supplied CD-ROM includes ScanSoft™
PaperPort™ 11SE. This software supports
Windows
®
2000 (SP4 or greater), XP (SP2 or
greater), XP Professional x64 Edition and
Windows Vista
®
. Update to the latest
Windows
®
Service Pack before installing
MFL-Pro Suite.
Note
If the Brother screen does not appear
automatically, go to My Computer (Computer),
double-click the CD-ROM icon, and then
double-click start.exe.
11
Windows
®
USB
Windows
®
Macintosh
®
USB
d When the ScanSoft™ PaperPort™ 11SE
License Agreement window appears, click
Yes if you agree to the Software License
Agreement.
e The installation of ScanSoft™ PaperPort™
11SE will automatically start and is followed by
the installation of MFL-Pro Suite.
f When the Brother MFL-Pro Suite Software
License Agreement window appears, click
Yes if you agree to the Software License
Agreement.
g Choose Local Connection, and then click
Next. The installation continues.
h When this screen appears, go to the next step.
Note
• If this screen appears, click OK and restart
your computer.
• If the installation does not continue
automatically, open the main menu again by
ejecting and then reinserting the CD-ROM or
double-click the start.exe program from the
root folder, and continue from b to install
MFL-Pro Suite.
• For Windows Vista
®
, when the User Account
Control screen appears, click Allow.
12
Windows
®
USB
16
Connect the USB cable
a Lift the scanner cover into the open position.
b Remove the USB label.
c Connect the USB cable to the USB socket
marked with a symbol. You will find the
USB socket inside the machine on the right as
shown below.
d Carefully guide the USB cable through the
trench as shown below, following the trench
around and toward the back of the machine.
Then connect the cable to your computer.
e Gently close the scanner cover using the finger
holds on both sides of it.
WARNING
Be careful not to trap your fingers under the
scanner cover.
Always use the finger holds provided on both
sides of the scanner cover when opening and
closing it.
Important
• DO NOT connect the machine to a USB port
on a keyboard or a non-powered USB hub.
• Connect the machine directly to your
computer.
LAN USB
Important
Make sure that the cable does not restrict the
cover from closing, or an error may occur.
13
Windows
®
USB
Windows
®
Macintosh
®
USB
17
Connect the power cord
a Connect the power cord.
The installation will continue automatically.
The installation screens appear one after
another.
b When the On-Line Registration screen is
displayed, make your selection and follow the
on-screen instructions.
18
Finish and restart
a Click Finish to restart your computer.
After restarting the computer, you must be
logged on with Administrator rights.
Now go to
Proceed to Install Optional Applications on
page 39.
Important
DO NOT cancel any of the screens during the
installation. It may take a few seconds for all
screens to appear.
Note
For Windows Vista
®
, when this screen appears,
click the check box and click Install to complete
the installation correctly.
Note
If an error message appears during the software
installation, run the Installation Diagnostics
located in Start/All Programs/Brother/
MFC-XXXX (where MFC-XXXX is your model
name).
Finish
The installation is now
complete.
14
Macintosh
®
USB
For USB Interface Users (For Mac OS
®
X 10.2.4 or greater)
14
Before you install
a Make sure your machine is connected to the
power and your Macintosh
®
is ON. You must
be logged on with Administrator rights.
15
Connect the USB cable
a Lift the scanner cover into the open position.
b Remove the USB label.
c Connect the USB cable to the USB socket
marked with a symbol. You will find the
USB socket inside the machine on the right as
shown below.
d Carefully guide the USB cable through the
trench as shown below, following the trench
around and toward the back of the machine.
Then connect the cable to your Macintosh
®
.
Important
• For Mac OS
®
X 10.2.0 to 10.2.3 users,
upgrade to Mac OS
®
X 10.2.4 or greater. (For
the latest information for Mac OS
®
X, visit
http://solutions.brother.com/
)
• Make sure there are no memory cards or a
USB Flash memory drive inserted.
Important
• DO NOT connect the machine to a USB port
on a keyboard or a non-powered USB hub.
• Connect the machine directly to your
Macintosh
®
.
Important
Make sure that the cable does not restrict the
cover from closing, or an error may occur.
LAN USB
15
Macintosh
®
USB
Windows
®
Macintosh
®
USB
e Gently close the scanner cover using the finger
holds on both sides of it.
WARNING
Be careful not to trap your fingers under the
scanner cover.
Always use the finger holds provided on both
sides of the scanner cover when opening and
closing it.
16
Install MFL-Pro Suite
a Put the supplied CD-ROM into your CD-ROM
drive.
b Double-click the Start Here OSX icon to install.
c Choose Local Connection, and then click
Next. Follow the on-screen instructions.
d The Brother software will search for the Brother
device. During this time the following screen
will appear.
e When this screen appears, click OK.
For Mac OS
®
X 10.3.x or greater, the
installation of MFL-Pro Suite is now
complete.
Go to step 17 on page 16.
f For Mac OS
®
X 10.2.4 to 10.2.8 users,
click Add.
g Choose USB.
Note
Please wait, it will take a few seconds for the
software to install. After the installation, click
Restart to finish installing the software.
16
Macintosh
®
USB
h Choose XXX-XXXX (where XXX-XXXX is your
model name), and then click Add.
i Click Print Center, then Quit Print Center.
The installation of MFL-Pro Suite is now
complete.
Go to step 17 on page 16.
17
Install
Presto! PageManager
When Presto! PageManager is installed OCR
capability is added to Brother ControlCenter2. You
can easily scan, share and organize photos and
documents using Presto! PageManager.
a Double-click the Presto! PageManager icon
and follow the on-screen instructions.
For Mac OS
®
X 10.2.4 to 10.3.8 users,
when this screen appears, click Go to
download the software from the Brother
Solutions Center website.
Finish
The installation is now
complete.
17
Windows
®
Wired Network
Windows
®
Macintosh
®
Wired Network
For Wired Network Interface Users
(For Windows
®
2000 Professional/XP/XP Professional x64 Edition/
Windows Vista
®
)
14
Before you install
a Make sure that your computer is ON and you
are logged on with Administrator rights.
b Disconnect the machine from the power
socket.
15
Connect the network
cable
a Lift the scanner cover into the open position.
b Connect the network cable to the LAN socket
marked with a symbol. You will find the
LAN socket inside the machine on the left as
shown below.
Important
• If there are any programs running, close
them.
• Make sure there are no memory cards or a
USB Flash memory drive inserted.
• The screens may differ depending on the
operating system.
• The supplied CD-ROM includes ScanSoft™
PaperPort™ 11SE. This software supports
Windows
®
2000 (SP4 or greater), XP (SP2 or
greater), XP Professional x64 Edition and
Windows Vista
®
. Update to the latest
Windows
®
Service Pack before installing
MFL-Pro Suite.
Important
Before installation, if you are
using personal firewall
software (other than Windows
®
Firewall), anti-spyware or
antivirus applications,
temporarily disable them.
LAN USB
18
Windows
®
Wired Network
c Carefully guide the network cable to the trench
as shown below, following the trench around
and toward the back of the machine. Then,
connect the cable to your network.
d Gently close the scanner cover using the finger
holds on both sides of it.
WARNING
Be careful not to trap your fingers under the
scanner cover.
Always use the finger holds provided on both
sides of the scanner cover when opening and
closing it.
16
Connect the power cord
a Connect the power cord.
Note
If both USB and LAN cables are being used,
guide both cables through the trench with one on
top of the other.
Important
Make sure that the cable does not restrict the
cover from closing, or an error may occur.
Important
If you have previously set up your machine for
a wireless network and then want to set it up
on a wired network, you should check that the
machine’s Network I/F is set to Wired LAN.
The wireless network interface will become
inactive with this setting.
On your machine, press MENU.
Press a or b to display Network and press
Network.
Press a or b to display Network I/F.
Press Network I/F.
Press Wired LAN.
Press Stop/Exit.
19
Windows
®
Wired Network
Windows
®
Macintosh
®
Wired Network
17
Install MFL-Pro Suite
a Put the supplied CD-ROM into your CD-ROM
drive. If the model name screen appears,
choose your machine. If the language screen
appears, choose your language.
b The CD-ROM main menu will appear. Click
Initial Installation.
c Click Install MFL-Pro Suite.
d When the ScanSoft™ PaperPort™ 11SE
License Agreement window appears, click
Yes if you agree to the Software License
Agreement.
e The installation of ScanSoft™ PaperPort™
11SE will automatically start and is followed by
the installation of MFL-Pro Suite.
f When the Brother MFL-Pro Suite Software
License Agreement window appears, click
Yes if you agree to the Software License
Agreement.
Note
If the Brother screen does not appear
automatically, go to My Computer (Computer),
double-click the CD-ROM icon, and then
double-click start.exe.
Note
• If this screen appears, click OK and restart
your computer.
• If the installation does not continue
automatically, open the main menu again by
ejecting and then reinserting the CD-ROM or
double-click the start.exe program from the
root folder, and continue from b to install
MFL-Pro Suite.
• For Windows Vista
®
, when the User Account
Control screen appears, click Allow.
20
Windows
®
Wired Network
g Choose Wired Network Connection, and
then click Next.
h For Windows
®
XP SP2/Windows Vista
®
users,
when this screen appears, choose Change the
Firewall port settings to enable network
connection and continue with the
installation. (Recommended) and click Next.
If you are using a firewall other than Windows
®
Firewall or Windows
®
Firewall is off, this screen
may appear.
See the instructions provided with your firewall
software for information on how to add the
following network ports.
For network scanning, add UDP port 54925.
For network PC-Fax receiving, add UDP port
54926.
If you still have trouble with your network
connection, add UDP port 137.
i The installation of the Brother drivers will
automatically start. The installation screens
appear one after another.
Note
• If the machine is configured for your network,
choose the machine from the list, and then click
Next.
This window will not appear if there is only one
machine connected on the network, it will be
chosen automatically.
If your machine shows APIPA in the IP
Address field, click Configure IP Address
and enter an IP address for your machine that
is suitable for your network.
• If the machine is not yet configured for use on
your network, the following screen appears.
Click OK.
The Configure IP Address window will
appear. Enter an IP address for your machine
that is suitable for your network by following the
on-screen instructions.
Important
DO NOT cancel any of the screens during the
installation. It may take a few seconds for all
screens to appear.
Note
For Windows Vista
®
, when this screen appears,
click the check box and click Install to complete
the installation correctly.
21
Windows
®
Wired Network
Windows
®
Macintosh
®
Wired Network
j When the On-Line Registration screen is
displayed, make your selection and follow the
on-screen instructions.
18
Finish and restart
a Click Finish to restart your computer. After
restarting the computer, you must be logged on
with Administrator rights.
19
Install MFL-Pro Suite on
additional computers
(If needed)
If you want to use your machine with multiple
computers on the network, install MFL-Pro Suite on
each computer. Go to step 17 on page 19.
Also see step 14-a on page 17 before you install.
Now go to
Proceed to Install Optional Applications on
page 39.
Note
If an error message appears during the software
installation, run the Installation Diagnostics
located in Start/All Programs/Brother/
MFC-XXXX (where MFC-XXXX is your model
name).
Note
This product includes a PC license for up to 2
users.
This license supports the installation of the
MFL-Pro Suite including ScanSoft™ PaperPort™
11SE on up to 2 PCs on the network.
If you want to use more than 2 PCs with
ScanSoft™ PaperPort™ 11SE installed, please
buy the Brother NL-5 pack which is a multiple PC
license agreement pack for up to 5 additional
users. To buy the NL-5 pack, contact your Brother
dealer.
Finish
The installation is now
complete.
22
Macintosh
®
Wired Network
For Wired Network Interface Users (For Mac OS
®
X 10.2.4 or greater)
14
Before you install
a Make sure your machine is connected to the
power and your Macintosh
®
is ON. You must
be logged on with Administrator rights.
15
Connect the network
cable
a Lift the scanner cover into the open position.
b Connect the network cable to the LAN socket
marked with a symbol. You will find the
LAN socket inside the machine on the left as
shown below.
Important
• For Mac OS
®
X 10.2.0 to 10.2.3 users,
upgrade to Mac OS
®
X 10.2.4 or greater. (For
the latest information for Mac OS
®
X, visit
http://solutions.brother.com/
)
• Make sure there are no memory cards or a
USB Flash memory drive inserted.
• If you have previously set up your machine
for a wireless network and then want to set
it up on a wired network, you should check
that the machine’s Network I/F is set to
Wired LAN. The wireless network interface
will be inactive with this setting. On your
machine, press MENU.
Press a or b to display Network and press
Network.
Press Network I/F.
Press Wired LAN.
Press Stop/Exit.
LAN USB
23
Macintosh
®
Wired Network
Windows
®
Macintosh
®
Wired Network
c Carefully guide the network cable to the trench
as shown below, following the trench around
and toward the back of the machine. Then,
connect the cable to your network.
d Gently close the scanner cover using the finger
holds on both sides of it.
WARNING
Be careful not to trap your fingers under the
scanner cover.
Always use the finger holds provided on both
sides of the scanner cover when opening and
closing it.
16
Install MFL-Pro Suite
a Put the supplied CD-ROM into your CD-ROM
drive.
b Double-click the Start Here OSX icon to install.
c Choose Wired Network Connection, and
then click Next. Follow the on-screen
instructions.
d The Brother software will search for the Brother
device. During this time the following screen
will appear.
Important
Make sure that the cable does not restrict the
cover from closing, or an error may occur.
Note
If both USB and LAN cables are being used,
guide both cables through the trench with one on
top of the other.
Note
Please wait, it will take a few seconds for the
software to install. After the installation, click
Restart to finish installing the software.
24
Macintosh
®
Wired Network
e When this screen appears, click OK.
For Mac OS
®
X 10.3.x or greater, the
installation of MFL-Pro Suite is now
complete.
Go to step 17 on page 25.
f For Mac OS
®
X 10.2.4 to 10.2.8 users,
click Add.
g Make the selection shown below.
h Choose XXX-XXXX (where XXX-XXXX is your
model name), and then click Add.
i Click Print Center, then Quit Print Center.
The installation of MFL-Pro Suite is now
complete.
Go to step 17 on page 25.
Note
• If the machine is configured for your network,
choose the machine from the list, and then click
OK. This window will not appear if there is only
one machine connected on the network, it will
be chosen automatically. Go to e.
• If this screen appears click OK.
Enter a name for your Macintosh
®
in Display
Name up to 15 characters long and click OK.
Go to e.
• If you want to use the machine’s Scan key to
scan over the network you must check the
Register your computer with the “Scan To”
function on the machine box.
• The name you enter will appear on the
machine’s LCD when you press the Scan key
and choose a scan option. (For more
information, see Network Scanning in the
Software User’s Guide on the CD-ROM.)
25
Macintosh
®
Wired Network
Windows
®
Macintosh
®
Wired Network
17
Install
Presto! PageManager
When Presto! PageManager is installed OCR
capability is added to Brother ControlCenter2. You
can easily scan, share and organize photos and
documents using Presto! PageManager.
a Double-click the Presto! PageManager icon
and follow the on-screen instructions.
For Mac OS
®
X 10.2.4 to 10.3.8 users,
when this screen appears, click Go to
download the software from the Brother
Solutions Center website.
18
Install MFL-Pro Suite on
additional computers
(If needed)
If you want to use your machine with multiple
computers on the network, install MFL-Pro Suite on
each computer. Go to step 16 on page 23. Also see
step 14-a on page 22 before you install.
Finish
The installation is now
complete.
26
For Wireless Network Users
For Wireless Network Interface Users
14
Before you begin
First you must configure the wireless network settings of your machine to communicate with your network
router/access point. After the machine is configured to communicate with your router/access point, computers on
your network will have access to the machine. To use the machine from these computers, you will need to install
the drivers and software. The following steps will guide you through the configuration and installation process.
To achieve optimum results with normal everyday document printing, place the Brother machine as close to the
network router/access point as possible with minimal obstructions. Large objects and walls between the two
devices as well as interference from other electronic devices can affect the data transfer speed of your documents.
Although the Brother MFC-6890CDW can be used in both a wired and wireless network, only one of the
connection methods can be used at a time.
Infrastructure Mode
a Router/Access Point
b Wireless Network machine (your machine)
c Wireless capable computer connected to the access point
d Wired computer connected to the access point
Important
If you have previously configured the wireless settings of the machine you must reset the network
(LAN) settings before you can configure the wireless settings again.
On your machine, press MENU. Press a or b to display Network and press Network.
Press a or b to display Factory Reset, and then press Factory Reset.
Press Yes to accept. Hold down Yes for 2 seconds to confirm.
Note
The following instructions are for infrastructure mode.
To set up your machine in any other wireless environment you can find instructions in the Network User's
Guide on the CD-ROM.
You can view the Network User’s Guide by following the instructions below.
1 Turn on your computer. Insert the Brother CD-ROM into your CD-ROM drive.
For Windows
®
:
2 Choose your model and the language. The CD-ROM main menu will appear.
3 Click Documentation, and then click HTML documents.
For Macintosh
®
:
2 Double-click Documentation, and then double-click your language folder.
3 Double-click top.html.
1
2
3
4
27
For Wireless Network Users
Wireless Network
15
Confirm your network environment (Infrastructure Mode)
The following instructions will offer two methods for installing your Brother machine in a wireless network
environment. Both methods are for infrastructure mode, using a wireless router/access point that uses DHCP to
assign IP addresses. Choose a configuration method and proceed to the page indicated.
a
If your wireless router/access point does not support SecureEasySetup™, Wi-Fi Protected Setup™
or AOSS™,
write down the wireless network settings
of your access point/router in the area below.
Important
If you do not know this information (Network Name (SSID ESSID), WEP key or WPA
passphrase), you cannot continue the wireless setup. You should see the documentation
provided with your access point or wireless router, consult the router manufacturer, or your
system administrator.
Item Example Record the current wireless network settings
Communication mode: (infrastructure) Infrastructure
Network name: (SSID, ESSID) HELLO
Authentication method:
(Open system, Shared key, WPA-PSK
1
,
WPA2-PSK
1
)
WPA2-PSK
Encryption mode:
(None, WEP,TKIP, AES)
AES
Network key:
(Encryption key, WEP key
2
, Passphrase)
12345678
1
WPA/WPA2-PSK is a Wi-Fi Protected Access™ Pre-Shared Key, which lets the Brother wireless machine associate with access
points using TKIP or AES encryption (WPA-Personal). WPA/WPA2-PSK (TKIP or AES) uses a Pre-Shared Key (PSK) that is 8
or more characters in length, up to a maximum of 63 characters.
2
The WEP key is for 64-bit encrypted networks or 128-bit encrypted networks and can contain both numbers and letters. If you
do not know this information you should see the documentation provided with your access point or wireless router. This key is a
64-bit or 128-bit value that must be entered in an ASCII or HEXADECIMAL format.
For example:
64-bit ASCII: Uses 5 text characters e.g. “Hello” (this is case sensitive)
64-bit Hexadecimal: Uses 10 digits of hexadecimal data e.g. “71f2234aba”
128-bit ASCII: Uses 13 text characters e.g.
“Wirelesscomms” (this is case sensitive)
128-bit Hexadecimal:
Uses 26 digits of hexadecimal data e.g.
“71f2234ab56cd709e5412aa3ba”
Now go to
page 28
b
If your wireless router/access point supports automatic wireless (one-push) setup
(SecureEasySetup™, Wi-Fi Protected Setup™ or AOSS™)
Now go to
page 30
28
For Wireless Network Users
Connecting the Brother machine to the wireless network
16
Configure the wireless
settings (Typical
Wireless Setup in
infrastructure mode)
a On your machine, press MENU.
Press a or b to display Network and press
Network.
Press WLAN.
Press Setup Wizard.
When Switch Network interface to
wireless? is displayed, press Yes to accept.
This will start the wireless setup wizard.
To cancel, press No.
b The machine will search for available SSIDs. If
a list of SSIDs is displayed, press a or b to
choose the SSID you wrote down in step 15 on
page 27. Press the SSID you want to connect
with. Go to f.
If your access point is set to not broadcast the
SSID you will have to manually add the SSID
name. Go to c.
c Press <New SSID>. Go to d.
d Enter the SSID you wrote down in step 15 on
page 27 using the Touchscreen.
You can use the d and c keys to move the
cursor left and right.
The letters appear in this order: lower case and
then upper case.
To enter numbers or special letters, press
repeatedly until the character you want to enter
appears.
(For more information, see Entering Text for
Wireless Settings on page 43.)
Press OK when you have entered all the
characters.
e Press Infrastructure.
f Choose one of the options below: If your
network is configured for Authentication and
Encryption you must match the settings used
for your network.
No Authentication or Encryption:
Press Open System, then press None for
Encryption Type? Then press Yes to
apply your settings. Go to i.
No Authentication with WEP Encryption:
Press Open System, then press WEP for
the Encryption Type? Go to g.
Authentication with WEP Encryption:
Press Shared Key. Go to g.
Authentication with WPA/WPA2-PSK
(TKIP or AES) Encryption:
Press WPA/WPA2-PSK. Go to h.
g Choose the appropriate key number. Enter the
WEP key you wrote down in step 15 on
page 27 on the Touchscreen.
You can use the d and c keys to move the
cursor left and right.
The letters appear in this order: lower case and
then upper case.
To enter numbers or special letters, press
repeatedly until the character you want to enter
appears.
(For more information, see Entering Text for
Wireless Settings on page 43.)
Press OK when you have entered all the
characters, then press Yes to apply your
settings. Go to i.
Note
It will take several seconds to display a list of
available SSIDs.
29
For Wireless Network Users
Wireless Network
h Press TKIP or AES for Encryption Type?
Enter the WPA/WPA2-PSK password you
wrote down in step 15 on page 27 using the
Touchscreen.
You can use the d and c keys to move the
cursor left and right.
The letters appear in this order: lower case and
then upper case.
To enter numbers or special letters, press
repeatedly until the character you want to enter
appears.
(For more information, see Entering Text for
Wireless Settings on page 43.)
Press OK when you have entered all the
characters, then press Yes to apply your
settings. Go to i.
i Your machine will now try to connect to your
wireless network using the information you
have entered. If successful, Connected will
appear on the LCD for approximately 1 minute.
If your machine does not successfully connect
to your network, verify your network settings
collected in step 15 on page 27 then repeat a
to h to make sure you have entered the correct
information.
If your access point does not have DHCP
enabled you will need to manually configure
the IP address, subnet mask and gateway of
the machine to suit your network. See the
Network User’s Guide for details.
Wireless setup is now complete. A four
level indicator at the top of your
machine’s LCD will show the wireless
signal strength of your router/access
point.
To install MFL-Pro Suite, continue to
step 17.
For Windows
®
Users:
Now go to
Page 32
For Mac OS
®
Users:
Now go to
Page 36
30
For Wireless Network Users
16
Configure the wireless
settings using the
automatic wireless (one-
push) method
a Confirm your wireless router/access point has
the SecureEasySetup™, Wi-Fi Protected
Setup™ or AOSS™ symbol as shown below.
b
Place the Brother machine within range of a
SecureEasySetup™, Wi-Fi Protected Setup™
or AOSS™ access point/router. The range may
differ depending on your environment. Refer to
the instructions provided with your router/access
point.
c Push the SecureEasySetup™, Wi-Fi Protected
Setup™ or AOSS™ button on your wireless
router/access point
.
See the user’s guide for your wireless
router/access point for instructions.
d On your machine, press MENU.
Press a or b to display Network and press
Network.
Press WLAN.
Press SES/WPS/AOSS.
When Switch Network interface to
wireless? is displayed, press Yes to accept.
This will start the wireless setup wizard.
To cancel, press No.
This feature will automatically detect which
mode (SecureEasySetup™, Wi-Fi Protected
Setup™ or AOSS™) your access point uses to
configure your machine.
e If the LCD shows Connected, the machine
has successfully connected to your
router/access point. You can now use your
machine in a wireless network.
If the LCD shows Setting WLAN,
Connecting SES (Connecting WPS or
Connecting AOSS), then
Connection Failed, the machine has not
successfully connected to your router/access
point. Try starting from c again. If the same
message is indicated again, reset the machine
back to the default factory settings and try
again. For resetting, see Restore the network
settings to factory default on page 43.
If the LCD shows
Setting WLAN
, then
Connection Failed
or
Incorrect Mode
, a
session overlap or connection failure was
detected (see the table below). The machine has
detected 2 or more router/access points on your
network that have the SecureEasySetup™, Wi-Fi
Protected Setup™ mode or AOSS™ mode
enabled. Make sure that only one router/access
point has the SecureEasySetup™, Wi-Fi
Protected Setup™ mode or AOSS™ mode
enabled and try starting from
c
again.
Wireless setup is now complete.
Note
If your wireless access point supports Wi-Fi
Protected Setup™ (PIN Method) and you want to
configure your machine using the PIN (Personal
Identification Number) Method, see Using the PIN
Method of Wi-Fi Protected Setup™ in the Network
User’s Guide on the CD-ROM.
LCD messages when using the
SES/WPS/AOSS control panel menu
Setting WLAN Searching or accessing the
access point and downloading
settings from the access point.
Connecting
SES/WPS/AOSS
Connecting to the access
point.
Connection
Failed
Connection failed. If this is
shown after the LCD shows
Connecting
SES/WPS/AOSS, a session
overlap was detected.
Incorrect
Mode
A session overlap was
detected.
Connected The machine has successfully
connected.
Note
If you encounter a problem during setup,
temporarily place your machine closer to the
wireless access point, and go back to c.
31
For Wireless Network Users
Wireless Network
Wireless setup is now complete. To
install MFL-Pro Suite, continue to
step 17.
For Windows
®
Users:
Now go to
Page 32
For Mac OS
®
Users:
Now go to
Page 36
32
Windows
®
Wireless Network
Install the Drivers & Software
(For Windows
®
2000 Professional/XP/XP Professional x64 Edition/
Windows Vista
®
)
17
Before you install
MFL-Pro Suite
a Make sure that your computer is ON and you
are logged on with Administrator rights.
18
Install MFL-Pro Suite
a Put the supplied CD-ROM into your CD-ROM
drive. If the model name screen appears,
choose your machine. If the language screen
appears, choose your language.
b The CD-ROM main menu will appear. Click
Initial Installation.
c Click Install MFL-Pro Suite.
Important
• If there are any programs running, close
them.
• Make sure there are no memory cards or a
USB Flash memory drive inserted.
• The screens may differ depending on the
operating system.
• The supplied CD-ROM includes ScanSoft™
PaperPort™ 11SE. This software supports
Windows
®
2000 (SP4 or greater), XP (SP2 or
greater), XP Professional x64 Edition and
Windows Vista
®
. Update to the latest
Windows
®
Service Pack before installing
MFL-Pro Suite.
Important
Before installation, if you are
using personal firewall
software (other than Windows
®
Firewall), anti-spyware or
antivirus applications,
temporarily disable them.
Note
If the Brother screen does not appear
automatically, go to My Computer (Computer),
double-click the CD-ROM icon, and then
double-click start.exe.
33
Windows
®
Wireless Network
Windows
®
Macintosh
®
Wireless Network
d When the ScanSoft™ PaperPort™ 11SE
License Agreement window appears, click
Yes if you agree to the Software License
Agreement.
e The installation of ScanSoft™ PaperPort™
11SE will automatically start and is followed by
the installation of MFL-Pro Suite.
f When the Brother MFL-Pro Suite Software
License Agreement window appears, click
Yes if you agree to the Software License
Agreement.
g Choose Wireless Network Connection, and
then click Next.
h Click on Checked and confirmed check box,
and then click Next.
i For Windows
®
XP SP2/Windows Vista
®
users,
when this screen appears, choose Change the
Firewall port settings to enable network
connection and continue with the
installation. (Recommended) and click Next.
If you are using a firewall other than Windows
®
Firewall or Windows
®
Firewall is off, this screen
may appear.
See the instructions provided with your firewall
software for information on how to add the
following network ports.
For network scanning, add UDP port 54925.
For network PC-Fax receiving, add UDP port
54926.
If you still have trouble with your network
connection, add UDP port 137.
Note
• If this screen appears, click OK and restart
your computer.
• If the installation does not continue
automatically, open the main menu again by
ejecting and then reinserting the CD-ROM or
double-click the start.exe program from the
root folder, and continue from b to install
MFL-Pro Suite.
• For Windows Vista
®
, when the User Account
Control screen appears, click Allow.
34
Windows
®
Wireless Network
j The installation of the Brother drivers will
automatically start. The installation screens
appear one after another.
k When the On-Line Registration screen is
displayed, make your selection and follow the
on-screen instructions.
Note
• If the machine is configured for your network,
choose the machine from the list, and then click
Next.
This window will not appear if there is only one
machine connected on the network, it will be
chosen automatically.
If your machine shows APIPA in the IP
Address field, click Configure IP Address
and enter an IP address for your machine that
is suitable for your network.
• If your wireless settings fail, an error message
will appear during the installation of MFL-Pro
Suite and the installation will be terminated. If
you encounter this failure, go to step 15 on
page 27 and setup the wireless connection
again.
• If you are using WEP and the LCD displayed
‘Connected’ but your machine is not found,
make sure you entered the WEP key correctly.
The WEP key is case sensitive.
• If the machine is not yet configured for use on
your network, the following screen appears.
Click OK.
The Configure IP Address window will
appear. Enter an IP address for your machine
that is suitable for your network by following the
on-screen instructions.
Important
DO NOT cancel any of the screens during the
installation. It may take a few seconds for all
screens to appear.
Note
For Windows Vista
®
, when this screen appears,
click the check box and click Install to complete
the installation correctly.
35
Windows
®
Wireless Network
Windows
®
Macintosh
®
Wireless Network
19
Finish and restart
a Click Finish to restart your computer. After
restarting the computer, you must be logged on
with Administrator rights.
20
Install MFL-Pro Suite on
additional computers
(If needed)
If you want to use your machine with multiple
computers on the network, install MFL-Pro Suite on
each computer. Go to step 17 on page 32.
Now go to
Proceed to Install Optional Applications on
page 39.
Note
If an error message appears during the software
installation, run the Installation Diagnostics
located in Start/All Programs/Brother/
MFC-XXXX (where MFC-XXXX is your model
name).
Note
This product includes a PC license for up to 2
users.
This license supports the installation of the
MFL-Pro Suite including ScanSoft™ PaperPort™
11SE on up to 2 PCs on the network.
If you want to use more than 2 PCs with
ScanSoft™ PaperPort™ 11SE installed, please
buy the Brother NL-5 pack which is a multiple PC
license agreement pack for up to 5 additional
users. To buy the NL-5 pack, contact your Brother
dealer.
Finish
The installation is now
complete.
36
Macintosh
®
Wireless Network
Install the Drivers & Software
(For Mac OS
®
X 10.2.4 or greater)
17
Before you install
MFL-Pro Suite
a Make sure your machine is connected to the
power and your Macintosh
®
is ON. You must
be logged on with Administrator rights.
18
Install MFL-Pro Suite
a Put the supplied CD-ROM into your CD-ROM
drive.
b Double-click the Start Here OSX icon to install.
c Choose Wireless Network Connection, and
then click Next.
d Click on the Checked and confirmed check
box, and then click Next.
Follow the on-screen instructions.
e The Brother software will search for the Brother
device. During this time the following screen
will appear.
Important
• For Mac OS
®
X 10.2.0 to 10.2.3 users,
upgrade to Mac OS
®
X 10.2.4 or greater. (For
the latest information for Mac OS
®
X, visit
http://solutions.brother.com/
)
• Make sure there are no memory cards or a
USB Flash memory drive inserted.
Note
Please wait, it will take a few seconds for the
software to install. After the installation, click
Restart to finish installing the software.
37
Macintosh
®
Wireless Network
Windows
®
Macintosh
®
Wireless Network
f When this screen appears, click OK.
For Mac OS
®
X 10.3.x or greater, the
installation of MFL-Pro Suite is now
complete.
Go to step 19 on page 38.
g For Mac OS
®
X 10.2.4 to 10.2.8 users,
click Add.
h Make the selection shown below.
i Choose XXX-XXXX (where XXX-XXXX is your
model name), and then click Add.
j Click Print Center, then Quit Print Center.
The installation of MFL-Pro Suite is now
complete.
Go to step 19 on page 38.
Note
• If the machine is configured for your network,
choose the machine from the list, and then click
OK.
This window will not appear if there is only one
machine connected on the network, it will be
chosen automatically. Go to f.
•
If your machine is not detected, go to step
15
on
page 27
and setup the wireless connection
again.
• If you are using WEP and the LCD displayed
‘Connected’ but your machine is not found,
make sure you entered the WEP key correctly.
The WEP key is case sensitive.
• If this screen appears click OK.
Enter a name for your Macintosh
®
in
Display Name up to 15 characters long and
click OK. Go to f.
• If you want to use the machine’s Scan key to
scan over the network you must check the
Register your computer with the “Scan To”
function on the machine box.
• The name you enter will appear on the
machine’s LCD when you press the Scan key
and choose a scan option. (For more
information, see Network Scanning in the
Software User’s Guide on the CD-ROM.)
38
Macintosh
®
Wireless Network
19
Install
Presto! PageManager
When Presto! PageManager is installed OCR
capability is added to Brother ControlCenter2. You
can easily scan, share and organize photos and
documents using Presto! PageManager.
a Double-click the Presto! PageManager icon
and follow the on-screen instructions.
For Mac OS
®
X 10.2.4 to 10.3.8 users,
when this screen appears, click Go to
download the software from the Brother
Solutions Center website.
20
Install MFL-Pro Suite on
additional computers
(If needed)
If you want to use your machine with multiple
computers on the network, install MFL-Pro Suite on
each computer. Go to step 17 on page 36.
Finish
The installation is now
complete.
39
Windows
®
Install Optional Applications
1
Install FaceFilter Studio
supported by
Reallusion, Inc
FaceFilter Studio is an easy-to-use borderless photo
printing application. FaceFilter Studio also lets you
edit your photo data and add photo effects such as
red eye reduction or skin tone enhancement.
a Open the main menu again by ejecting and
then reinserting the CD-ROM or by double-
clicking the start.exe program from the root
folder.
b The CD-ROM main menu will appear. Choose
your language and then click Additional
Applications.
c Click the FaceFilter Studio button to install.
2
Install FaceFilter Studio
Help
To get instructions on how to use FaceFilter Studio,
download and install FaceFilter Studio Help.
a To run FaceFilter Studio, go to
Start/All Programs/Reallusion/
FaceFilter Studio on your computer.
b Click the button on the upper right corner
of the screen.
c Click Check for updates to go to the
Reallusion update web page.
d Click the Download button and choose a folder
to save the file in.
e Close FaceFilter Studio before you start the
installer for FaceFilter Studio Help.
Double-click the downloaded file from the
folder you specified and follow the on-screen
instructions for installation.
Important
• The machine must be ON and connected to
the computer.
• The computer must be connected to the
Internet.
• Make sure you are logged on with
Administrator rights.
Note
To view the complete FaceFilter Studio Help,
choose Start/All Programs/Reallusion/
FaceFilter Studio/FaceFilter Studio Help on
your computer.
40
Windows
®
Install Optional Applications
3
Install
BookScan&Whiteboard
Suite supported by
Reallusion, Inc
You can install BookScan&Whiteboard Suite.
The BookScan Enhancer software can correct your
scanned book images automatically. The
Whiteboard Enhancer software cleans up and
enhances text and images from photos taken of your
whiteboard. (Internet access required.)
a Open the main menu again by ejecting and
then reinserting the CD-ROM or by double-
clicking the start.exe program from the root
folder.
b The CD-ROM main menu will appear. Choose
your language and then click Additional
Applications.
c Click the BookScan&Whiteboard Suite
button to install.
Important
• The machine must be ON and connected to
the computer.
• The computer must be connected to the
Internet.
41
For Network Users
BRAdmin Light utility (For Windows
®
users)
BRAdmin Light is a utility for initial setup of Brother network connected devices. It also can search for Brother
products on your network, view the status and configure basic network settings, such as IP address.
For more information on BRAdmin Light, visit us at http://solutions.brother.com/
.
Install the BRAdmin Light
configuration utility
a Click Network Utilities on the menu screen.
b Click BRAdmin Light and follow the on-screen
instructions.
Set your IP address, Subnet Mask
and Gateway using BRAdmin Light
a Start BRAdmin Light. It will search for new
devices automatically.
b Double-click the unconfigured device.
c Choose STATIC for the Boot Method. Enter
the IP Address, Subnet Mask and Gateway,
and then click OK.
d The address information will be saved to the
machine.
Note
If you require more advanced printer management, use the latest Brother BRAdmin Professional utility version
that is available as a download from http://solutions.brother.com/
.
Note
If you have a DHCP/BOOTP/RARP server in your
network, you don’t have to do the following
operation. The machine will automatically obtain
its own IP address.
Note
The default password for the machine is ‘access’.
You can use BRAdmin Light to change this
password.
42
For Network Users
BRAdmin Light utility (For Mac OS
®
X users)
BRAdmin Light is a utility for initial setup of Brother network connected devices. It also can search for Brother
products on your network, view the status and configure basic network settings, such as IP address from a
computer running Mac OS
®
X 10.2.4 or greater.
The BRAdmin Light software will be installed automatically when you install the printer driver. If you have already
installed the printer driver, you don’t have to install BRAdmin Light again. For more information on BRAdmin Light,
visit us at http://solutions.brother.com/
.
Set your IP address, Subnet Mask
and Gateway using BRAdmin Light
a Double-click the Macintosh HD icon on your
desktop.
b Choose Library, Printers, Brother and then
Utilities.
c Double-click the file BRAdmin Light.jar and
run the software. BRAdmin Light will then
search for new devices automatically.
d Double-click the unconfigured device.
e Choose STATIC for the Boot Method. Enter
the IP Address, Subnet Mask and Gateway,
and then click OK.
f The address information will be saved to the
machine.
Note
• If you have a DHCP/BOOTP/RARP server in
your network, you don’t have to do the
following operation. The machine will
automatically obtain its own IP address.
• Make sure that version 1.4.1_07 or later of
Java™ client software is installed on your
computer.
• The default password for the machine is
‘access’. You can use BRAdmin Light to
change this password.
43
For Wireless Network Users
Restore the network settings to factory default
To restore all network settings of the internal Print/Scan server to factory default, please follow the steps below.
a Make sure the machine is not operating, then disconnect all the cables from the machine (except the power
cord).
b Press MENU.
c Press a or b to display Network and press Network.
d Press a or b to display Factory Reset and press Factory Reset.
e Press Yes.
f Hold down Yes for 2 seconds to confirm.
g The machine will restart, re-connect cables once this is complete.
Entering Text for Wireless Settings
When you are setting certain menu selections, you may need to enter text into the machine. Press to choose
numbers, characters and special characters. Up to four letters are assigned to each button on the Touchscreen.
By pressing the correct button repeatedly, you can access the character you want.
Inserting spaces
To enter a space, press to choose special characters, then press the space button or .
Making corrections
If you entered an incorrect letter and want to change it, use d or c to move the cursor under the incorrect character.
Then press . Re-enter the correct character. You can also insert letters by moving the cursor and entering a
character.
Repeating letters
If you need to enter a letter that is on the same button as the letter before, press c to move the cursor to the right
before you press the button again.
OK
Note
The characters available may differ depending on your country.
Consumables
Replacement consumables
When the time comes to replace ink cartridges, an error message will be indicated on the LCD. For more
information about the ink cartridges for your machine, visit http://www.brother.com/original/
or contact your local
Brother re-seller.
Ink cartridge
Trademarks
The Brother logo is a registered trademark of Brother Industries, Ltd.
Brother is a registered trademark of Brother Industries, Ltd.
Multi-Function Link is a registered trademark of Brother International Corporation.
Windows Vista is either a registered trademark or a trademark of Microsoft Corporation in the United States and other countries.
Microsoft, Windows and Windows Server are registered trademarks of Microsoft Corporation in the United States and/or other countries.
Macintosh and TrueType are registered trademarks of Apple Inc.
Nuance, the Nuance logo, PaperPort and ScanSoft are trademarks or registered trademarks of Nuance Communications, Inc. or its affiliates
in the United States and/or other countries.
PictBridge is a trademark.
FaceFilter Studio is a trademark of Reallusion, Inc.
BROADCOM, SecureEasySetup and the SecureEasySetup logo are trademarks or registered trademarks of Broadcom Corporation in the
United States and/or other countries.
AOSS is a trademark of Buffalo Inc.
Wi-Fi, WPA, WPA2 and Wi-Fi Protected Setup are either trademarks or registered trademarks of Wi-Fi Alliance in the United States and/or
other countries.
Each company whose software title is mentioned in this manual has a Software License Agreement specific to its proprietary programs.
All other brand and product names mentioned in this manual are trademarks or registered trademarks of their
respective companies.
Compilation and Publication
Under the supervision of Brother Industries, Ltd., this manual has been compiled and published, covering the latest product descriptions and
specifications.
The contents of this manual and the specifications of this product are subject to change without notice.
Brother reserves the right to make changes without notice in the specifications and materials contained herein and shall not be responsible for
any damages (including consequential) caused by reliance on the materials presented, including but not limited to typographical and other
errors relating to the publication.
Copyright and License
©2008 Brother Industries, Ltd.
This product includes software developed by the following vendors:
©1983-1998 PACIFIC SOFTWORKS, INC.
This product includes the “KASAGO TCP/IP” software developed by ELMIC WESCOM, Inc.
©2007 Devicescape Software, Inc.
Black Yellow Cyan Magenta
LC1100BK (Standard)
LC1100HY-BK (High Yield)
LC1100Y (Standard)
LC1100HY-Y (High Yield)
LC1100C (Standard)
LC1100HY-C (High Yield)
LC1100M (Standard)
LC1100HY-M (High Yield)
What is Innobella™?
Innobella™ is a range of genuine consumables offered by Brother.
The name "Innobella™" derives from the words "Innovation" and "Bella"
(meaning "Beautiful" in Italian) and is a representation of the "innovative"
technology providing you with "beautiful" and "long lasting" print results.
1 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Brother MFC-6890CDW bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Brother MFC-6890CDW in de taal/talen: Engels als bijlage per email.

De handleiding is 3,7 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Brother MFC-6890CDW

Brother MFC-6890CDW Installatiehandleiding - Nederlands - 44 pagina's

Brother MFC-6890CDW Gebruiksaanwijzing - Nederlands - 238 pagina's

Brother MFC-6890CDW Installatiehandleiding - Deutsch - 44 pagina's

Brother MFC-6890CDW Gebruiksaanwijzing - Deutsch - 243 pagina's

Brother MFC-6890CDW Gebruiksaanwijzing - English - 233 pagina's

Brother MFC-6890CDW Installatiehandleiding - Français - 44 pagina's

Brother MFC-6890CDW Gebruiksaanwijzing - Français - 246 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info