555741
24
Verklein
Vergroot
Pagina terug
1/81
Pagina verder
14
CONTENTS INDEXMAINTENANCE
KNOWING YOUR
SEWING MACHINE
STRAIGHT AND
ZIGZAG STITCHING
BUILT-IN STITCHES
BUTTONHOLE AND
BUTTON SEWING
USING ATTACHMENTS
AND APPLICATIONS
THREADING THE MACHINE
Winding the Bobbin
1. Place the spool of thread on the spool pin and pass the thread
around the bobbin winding tension disc.
1 Bobbin winding tension disc
2 Bobbin winder
2. Pass the end of the thread through the hole in the bobbin from the
inside.
3. Place the bobbin onto the bobbin winding shaft and slide the shaft
to the right. Turn the bobbin clockwise, by hand, until the spring
on the shaft slides into the slit on the bobbin.
3 Spring
4 Slit
4. While holding the end of the thread, gently press on the foot con-
troller to wind the thread around the bobbin a few times, then stop
the machine.
5. Trim the excess thread sticking out from the top of the bobbin and
continue winding the thread onto the bobbin by pressing down on
the foot controller.
NOTE:
The machine stops automatically when the bobbin is full.
6. When the machine stops, cut the thread between bobbin and spool,
push the shaft to the left and remove the full bobbin from the shaft.
CAUTION:
Although the needle bar does not move when the bobbin winding
shaft is slid toward the bobbin presser, the balance wheel will con-
tinue to turn. Therefore, do not touch the balance wheel while the
bobbin is being wound.
ENFILAGE DE LA MACHINE
Remplissage de la canette
1. Placer la bobine de fil sur le porte-bobine et faire passer le fil par le
disque de tension du dévidoir.
1
Disque de tension du dévidoir
2
Remplissage de la canette
2. Faire passer lextrémité du fil dans lorifice de la canette par linté-
rieur.
3. Placer la canette sur le dévidoir et le faire glisser vers la droite.
Faire tourner la canette dans le sens des aiguilles dune montre,
manuellement, jusqu’à ce que le ressort de la broche se place dans
la rainure de la canette.
3
Ressort
4
Rainure
4. En tenant lextrémité du fil, appuyer légèrement sur la pédale pour
embobiner le fil sur la canette plusieurs fois, puis arrêter la ma-
chine.
5. Couper le morceau de fil dépassant en haut de la canette et conti-
nuer dembobiner le fil sur la canette en appuyant sur la pédale.
REMARQUE :
La machine sarrête automatiquement lorsque la canette est pleine.
6. Lorsque la machine sarrête, couper le fil entre la canette et la bo-
bine, pousser le dévidoir vers la gauche et en retirer la canette
pleine.
PRECAUTION :
Bien que la barre à aiguille ne se déplace pas lorsque la broche du
dévidoir est glissée vers le butoir de la canette, le volant à main con-
tinuera de tourner. Par conséquent, ne pas le toucher durant le rem-
plissage de la canette.
ENHEBRADO DE LA MÁQUINA
Bobinado de la canilla
1. Coloque un carrete de hilo en el portacarretes y pase el hilo por
el disco de tensión de bobinado de la canilla.
1 Disco de tensión de bobinado de la canilla
2 Bobinado de la canilla
2. Pase el extremo del hilo por el orificio de la canilla desde el inte-
rior.
3. Coloque la canilla en el eje de bobinado y deslice dicho eje hacia
la derecha. Gire la canilla con la mano en el sentido de las mani-
llas de un reloj, hasta que el muelle impulsor del eje se deslice
dentro de la ranura de la canilla.
3 Muelle
4 Ranura
4. Sujetando el extremo del hilo, presione suavemente el pedal para
que el hilo efectúe un par de vueltas alrededor de la canilla y
pare la máquina.
5. Deshaga el exceso de hilo arriba de la canilla. Siga bobinando el
hilo en la canilla presionando el pedal.
NOTA:
La máquina se para automáticamente cuando la canilla está llena.
6. Cuando la máquina se pare, corte el hilo entre la canilla y el ca-
rrete, empuje el eje hacia la izquierda y retire la canilla llena del
eje.
ATENCIÓN:
Aunque la barra de la aguja no se desplace cuando el eje de
bobinado de la canilla se deslice hacia el apretador de la cani-
lla, la ruedecilla va a seguir girando y no puede tocarse mien-
tras la canilla esté bobinando.
ENFIAMENTO DA LINHA NA
MÁQUINA
Enrolamento da Bobina
1. Coloque o carretel de linha no porta-carretel e passe a linha ao redor do
disco tensor de enrolamento da bobina..
1 Disco tensor de enrolamento da bobina
2 Enrolador de bobina
2. Passe a ponta da linha através do orifício na bobina pelo lado de dentro.
3. Coloque a bobina no eixo do enrolador de bobina e deslize o eixo para a
direita. Gire a bobina no sentido horário com a mão, até que a molinha
no eixo se deslize para dentro da fenda na bobina.
3 Molinha
4 Fenda
4. Enquanto segura a ponta da linha, pressione gentilmente o reostato para
enrolar a linha ao redor da bobina algumas vezes, e então pare a máqui-
na.
5. Apare o excesso de linha que transpassa para fora pelo topo da bobina e
continue a enrolar o fio na bobina pressionando o reostato.
NOTA:
A máquina parará automaticamente quando a bobina estiver cheia.
6. Quando a máquina parar, corte a linha entre a bobina e o carretel, em-
purre o eixo para a esquerda e remova a bobina cheia do eixo.
AVISO:
Embora a barra de agulha não se mova quando o eixo do enrolador de
bobina for deslizado em direção ao pedal da bobina, o volante continu-
ará a girar. Portanto, não toque no volante enquanto a bobina estiver
sendo enrolada.
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Brother LS1217 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Brother LS1217 in de taal/talen: Engels, Frans, Portugees, Spaans als bijlage per email.

De handleiding is 1,32 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info