631248
111
Verklein
Vergroot
Pagina terug
1/116
Pagina verder
109
4
The thread does
not pass through
the eye of the
needle.
The needle was not raised.
Press (needle position button)
once or twice to raise the needle.
page 21
The needle is incorrectly installed. Correctly install the needle. page 31
The stitch is not
sewn correctly.
The appropriate presser foot for the
type of stitch that you wish to sew is
not used.
Attach the presser foot that is
appropriate for the type of stitch that
you wish to sew.
page 89
The thread tension is incorrectly set. Adjust the thread tension. page 49
The thread is tangled, for example, in
the bobbin case.
Remove the tangled thread. If the
thread is tangled in the bobbin case,
clean the race.
page 95
The fabric does
not feed.
The feed dogs are lowered.
Slide the feed dog position switch to
.
page 75
The stitch is too short. Lengthen the stitch length. page 42
The combination of fabric, thread and
needle is incorrect.
Select a thread and needle that are
appropriate for the type of fabric
being sewn.
page 30
The thread is tangled, for example, in
the bobbin case.
Remove the tangled thread. If the
thread is tangled in the bobbin case,
clean the race.
page 95
Zigzag foot “J” is slanted on a thick
seam at the beginning of stitching.
Use the presser foot locking pin
(black button on the left side) on
zigzag foot “J” to keep the presser
foot level while sewing.
page 51
The sewing lamp
does not come
on.
The sewing lamp is damaged.
Contact your dealer or the nearest
authorized service center.
While winding
the bobbin, the
bobbin thread
was wound
below the bobbin
winder seat.
You have not wound the bobbin thread
properly.
After removing the thread wound below
the bobbin winder seat, wind the
bobbin correctly.
page 104
Bobbin thread
does not wind
neatly on the
bobbin.
The thread is not passed through the
bobbin-winding thread guide correctly.
Correctly pass the thread through the
bobbin-winding thread guide.
page 15
Bobbin spins slowly.
Move the sewing speed controller to the
right (so that the speed will be fast).
page 17
The thread that was pulled out was not
wound onto the bobbin correctly.
Wind the thread that was pulled off
round the bobbin five or six times
clockwise.
page 17
Fabric being
sewn with the
machine cannot
be removed.
Thread is tangled below the needle
plate.
Lift up the fabric and cut the threads
below it, and clean the race.
page 101
The fabric feeds
in the opposite
direction.
The feed mechanism is damaged.
Contact your dealer or the nearest
authorized service center.
The upper thread
has tightened up.
The bobbin thread is incorrectly
installed.
Correctly install the bobbin thread. page 18 , 97
The thread is
tangled on the
wrong side of the
fabric.
You have not threaded the upper thread
properly.
Correct the upper threading. page 20 , 98
Symptom Probable Cause Remedy Reference
111

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Brother JK7000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Brother JK7000 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,87 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info