718770
172
Verklein
Vergroot
Pagina terug
1/180
Pagina verder
ERROR MESSAGES
A-22
If the machine is not properly set and the “Start/Stop” button is pressed, or if the operation procedure is
incorrect, the machine does not start. An alarm sounds and an error message is displayed on the LCD. If
an error message displays, follow the instructions in the message.
Below is an explanation of error messages. Refer to these when necessary (if you press or do the
operation correctly while the error message is displayed, the message disappears).
Specifying with
sensor pen cannot be
done accurately
The sensor pen has not been calibrated. Before using the sensor pen for the first time,
be sure to calibrate it.
B-56
The pen is being held differently than when it
was calibrated.
When using the sensor pen, be sure to hold it
at the same angle as when it was calibrated.
The specification location may be misaligned
if the pen is held at a slightly different angle.
In this case, make fine adjustments after
making the selection.
B-56
CAUTION
This machine is equipped with a thread detection device. If the “Start/Stop” button is pushed before the
upper threading is done, the machine will not operate properly. Also, depending on the pattern selected,
the machine may feed the fabric even if the needle is raised. This is due to the needle bar release
mechanism. At these times, the machine will make a sound different from what is made during normal
sewing. This is not the sign of a malfunction.
If the power is disconnected during sewing:
Turn the main power to OFF and unplug the machine.
If you restart the machine, follow the instructions for operating the machine correctly.
ERROR MESSAGES
CAUTION
Be sure to rethread the machine. If you press the “Start/Stop” button without rethreading the machine,
the thread tension may be wrong or the needle may break and cause injury.
Marks Error Messages Cause/Solution
A malfunction occurred.Turn the machine off, then on again. This message is displayed if some malfunction occurs.
Attach the embroidery frame. This message appears if the embroidery frame is not attached
when you press in the embroidery screen. (see page
B-58)
Check and rethread the upper thread. This message is displayed when the upper thread is broken or
not threaded correctly, and the “Start/Stop” button is pressed.
Data volume is too large for this pattern. This message is displayed when the patterns you are editing
take up too much memory, or if you are editing too many
patterns for the memory.
Failed to save file. This message appears when you try to save more than 100
settings screen image files in the USB media. In this case,
delete a file from the USB media or use different USB media.
(see page B-28)
Lower the presser foot lever. This message is displayed when the “Presser Foot Lifter”
button is pushed while the presser foot lever is raised/the
needle is lowered.
Move the sensor pen away from the currently marked position. This message appears when you press down the sensor pen
tip before pressing and keep pressing for the certain
period. Move the sensor pen away from the current position.
Problem Cause Solution Page
172

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Brother Innov-is V3 LE bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Brother Innov-is V3 LE in de taal/talen: Engels als bijlage per email.

De handleiding is 14 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Brother Innov-is V3 LE

Brother Innov-is V3 LE Gebruiksaanwijzing - Nederlands - 180 pagina's

Brother Innov-is V3 LE Gebruiksaanwijzing - Deutsch - 180 pagina's

Brother Innov-is V3 LE Gebruiksaanwijzing - Français - 180 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info