718739
123
Verklein
Vergroot
Pagina terug
1/132
Pagina verder
Troubleshooting
Appendix A-21
MAINTENANCE AND TROUBLESHOOTING
A
Error messages
If the “Start/Stop” button is pressed before the machine is correctly set up or if an operation is performed incorrectly, an error
message appears in the LCD. Follow the instructions that appear. The message will disappear if or is pressed while the
message is displayed.
Error Messages Cause Solution
1 This message is displayed when a button, such as
the “Start/Stop” button, was pressed while the
presser foot was raised.
Lower the presser foot lever before continuing the
operation.
2 This message is displayed when the buttonhole lever
is down, a stitch other than a buttonhole is selected,
and a button, such as the “Start/Stop” button, is
pressed.
Lift the buttonhole lever before continuing the
operation.
3 This message is displayed when the buttonhole lever
is up, a buttonhole stitch is selected, and a button,
such as the “Start/Stop” button, is pressed.
Lower the buttonhole lever before continuing the
operation.
4 This message is displayed when a button, such as
the Reverse/reinforcement stitch button, was
pressed while the bobbin winder shaft is moved to
the right.
Move the bobbin winder shaft to the left before
continuing the operation.
5 This message is displayed when the “Start/Stop”
button was pressed while the foot controller was
connected.
Disconnect the foot controller, and then press the
“Start/Stop” button. Otherwise, operate the machine
by using the foot controller.
6 The motor locked up because the thread became
tangled, or the needle bent and thus hit the needle
plate.
Clean the race to remove the tangled thread (refer to
page A-2).
Check the needle. If the needle is bent or broken,
replace the needle. For details, refer to “Checking the
needle” and “Replacing the needle” in the “Basic
operations” section.
If both of the above fail, refer to “Error message
“E06” appears in the LCD” on page A-13.
7 This message is displayed when a button, such as
the “Start/Stop” button, was pressed after a stitch
has been deleted.
Select a pattern before continuing the operation.
8 This message is displayed when the sewing speed
controller is set to control the zigzag stitch width,
and the “Start/Stop” button is pressed.
Turn off the width control, or use the foot controller to
operate the machine. For details, refer to “Satin
stitching using the sewing speed controller” in the
“Sewing” section.
9
This message is displayed when (Twin needle) is
turned on, and a stitch pattern that cannot be sewn
with the twin needle is selected.
Switch to the single needle mode, and replace the
twin needle with a single needle before continuing
the operation.
10 This message is displayed when you try to sew with
a stitch other than a straight stitch (middle needle
position) while the straight stitch needle plate is
installed.
Turn off the machine, and then replace the needle
plate before continuing the operation.
11 This message is displayed when the needle plate
cover is removed while the machine is still turned on.
Turn off the machine, and then attach the needle
plate cover before continuing the operation.
12
F**
If error message “F**” appears in the LCD while the
machine is being used, the machine may be
malfunctioning.
Contact your nearest Brother authorized service
center.
123

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Brother-Innov-is-F410

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Brother Innov-is F410 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Brother Innov-is F410 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,37 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Brother Innov-is F410

Brother Innov-is F410 Gebruiksaanwijzing - Nederlands - 132 pagina's

Brother Innov-is F410 Gebruiksaanwijzing - Deutsch - 132 pagina's

Brother Innov-is F410 Gebruiksaanwijzing - Français - 132 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info