Handleiding Bowers Wilkins Z2 (pagina 7 van 145) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Zweeds, Noors)

548944

Verklein

Vergroot

Pagina terug

1/145

Pagina verder

ENGLISH

4. The Z2 Indicator

The Z2 indicator illuminates in a range of colours

to indicate different operational conditions. Table 1

describes the colours and their meanings.

5. Joining Wireless Networks and

conguring iTunes

In order to play your iTunes music on your Z2 using

AirPlay, your Z2 must join the same network as the

computer on which iTunes is installed and running.

Z2 network addressing is set to DHCP which means

that once it has joined the wireless network it will

not require any further conguration. You will need

to know your home wireless network name and

password before you start.

Note: You will need to disconnect the power

if you have already used your product without

conguring a wireless network.

5.1 Set up your Z2 with your iOS device

(iPod touch, iPad or iPhone)

• Get ‘Bowers & Wilkins Control’ App from the

App Store or by visiting www.bowers-wilkins.

com/control

• Follow the onscreen instructions.

5.2 Set up with Mac or PC

• Get ‘Bowers & Wilkins Control’ App from the

App Store or by visiting www.bowers-wilkins.

com/control

5.3 Setting up Z2 using a wired

connection

To set up Z2 to join your wireless network you

should rst connect it physically to the Mac/PC using

an Ethernet cable. You will need to ensure that your

Mac/PC wireless capabilities are disabled. Once

connected you can browse to the Z2 setup page.

Follow the steps described below.

Note: Z2 can also use a wired network for AirPlay

streaming.

• Unplug every cable from the Z2 and undock any

docked iPod or iPhone.

• Using an Ethernet cable connect the Z2 rear panel

ETHERNET socket to an Ethernet socket on the

computer.

• Connect the power cable. Z2 will switch on with

the indicator pulsing red.

• Once the Z2 indicator begins to ash yellow.

Press and hold the '+' volume button on Z2 for 4

seconds. Z2's indicator will show solid purple once

the wired network connection is established.

• Using an internet browser application running on

the computer connected to the Z2 type the Z2

default network address (http://169.254.1.1) in

the browser address eld and press “return”. This

will open the Z2 setup page.

• The setup page provides the option to change

the Z2 name. Changing the name is useful if more

than one Z2 is to be connected to the network.

Enter a new name (Z2 Kitchen for example) in the

Name box.

• Select your home network Name from the

drop down list and enter the Password in the

appropriate box. Take care to type the password

correctly.

• When you are nished, click on the Apply button,

then close the Z2 setup page. Disconnect the

Ethernet cable.

• The Z2 indicator will change to steady purple when

the wireless network connection is established.

This will take up to 3 minutes.

Note: If Z2 fails to connect to your home wireless

network, the most likely fault is an incorrectly

entered network password. Follow the reset

instructions in Section 7 and begin the network

setup procedure again.

5.4 Conguring iTunes

With Z2 connected to your home network (wired or

wireless) you can congure iTunes to use it as an

output device. Select Z2 as an output option in the

pop-up AirPlay menu. iTunes will now play through

the Z2.

Multiple Z2 units can be connected to the wireless

network and used to provide audio in separate

rooms. Each will be available in the iTunes devices

menu, identied by either the names specied in the

setup page, or by default the last three digits of their

serial numbers.

Indicator Colour Meaning Input Selected

Off Standby N/A

Dim Red Sleep N/A

Pulsing Red Powering up N/A

Flash Red twice Reset started N/A

Blue On Dock

Fast ashing Blue Volume adjustment Dock

Orange On Aux

Fast ashing Orange Volume adjustment Aux

Purple On AirPlay

Fast ashing purple Volume adjustment AirPlay

Slow ashing purple No network connected AirPlay

Fast ashing Red Invalid operation Any

Slow ashing Yellow Wireless setup mode N/A

White Firmware update N/A

Flashing white Firmware error N/A

Table 1

Indicator colour and meaning

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Bowers Wilkins Z2 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info