Feed the cable through the clearance holes in the
wave plate and connect to the terminals (figure 7),
following the instructions in the section “Connections”.
Taking care with the positioning of excess cable,
attach the wave cover to the wall plate.
Connections (figure 8)
All connections should be made with the equipment
switched off.
Connect the positive terminal on the speaker (marked
+ and coloured red) to the positive output terminal of
the amplifier and negative (marked – and coloured
black) to negative. Incorrect connection can result in
poor imaging and loss of bass.
Ask your dealer for advice when choosing cable. Keep
the total impedance below the maximum
recommended in the specification and use a low
inductance cable to avoid attenuation of the highest
frequencies.
Fine tuning
Before fine tuning, double check that all the
connections in the installation are correct and secure.
To reduce the bass level, fit a foam plug into one or
both the port tubes (figure 9). To access the ports,
remove the grille by gently pulling it away from the
cabinet.
If the sound is too harsh, increase the amount of soft
furnishing in the room (for example use heavier
curtains), or reduce it if the sound is dull and lifeless.
Test for flutter echoes by clapping your hands and
listening for rapid repetitions. They can be reduced by
the use of irregular shaped surfaces such as
bookshelves and large pieces of furniture.
Running-in Period
The performance of the speaker will change subtly
during the initial listening period. If the speaker has
been stored in a cold environment, the damping
compounds and suspension materials of the drive
units will take some time to recover their correct
mechanical properties. The drive unit suspensions will
also loosen up during the first hours of use. The time
taken for the speaker to achieve its intended
performance will vary depending on previous storage
conditions and how it is used. As a guide, allow up to
a week for the temperature effects to stabilise and
15 hours of average use for the mechanical parts to
attain their intended design characteristics.
However, longer run-in periods (as long as a month)
have been reported and there is evidence to suggest
that this has little to do with the speaker changing and
more to do with the listener getting used to the new
sound. This is especially so with highly revealing
speakers such as these where there may be a
significant increase in the amount of detail compared
with what the listener has previously been used to; the
sound may at first appear too “up front” and perhaps
a little hard. After an extended period of time the
sound will seem to mellow, but without losing clarity
and detail.
Aftercare
The cabinet surfaces usually only require dusting. If
you wish to use an aerosol or other cleaner, remove
the grille first by gently pulling it away from the
cabinet. Spray aerosols onto the cleaning cloth, not
directly onto the product. Test a small area first, as
some cleaning products may damage some of the
surfaces. Avoid products that are abrasive, or contain
acid, alkali or anti-bacterial agents. Do not use
cleaning agents on the drive units. The grille fabric
may be cleaned with a normal clothes brush whilst the
grille is detached from the cabinet. Avoid touching the
drive units, especially the tweeter, as damage may
result.
Limited Warranty
This product has been designed and manufactured to
the highest quality standards. However, if something
does go wrong with this product, B&W Group Ltd. and
its national distributors warrant free of charge labour
(exclusion may apply) and replacement parts in any
country served by an official B&W distributor.
This limited warranty is valid for a period of five years
from the date of purchase or two years for electronics
including amplified loudspeakers.
Terms and Conditions
1 The warranty is limited to the repair of the
equipment. Neither transportation, nor any other
costs, nor any risk for removal, transportation and
installation of products is covered by this warranty.
2 This warranty is only valid for the original owner. It
is not transferable.
3 This warranty will not be applicable in cases other
than defects in materials and/or workmanship at
the time of purchase and will not be applicable:
a. for damages caused by incorrect installation,
connection or packing,
b. for damages caused by any use other than correct
use described in the user manual, negligence,
modifications, or use of parts that are not made or
authorised by B&W,
c. for damages caused by faulty or unsuitable
ancillary equipment,
d. for damages caused by accidents, lightning, water,
fire heat, war, public disturbances or any other
cause beyond the reasonable control of B&W and
its appointed distributors,
e. for products whose serial number has been
altered, deleted, removed or made illegible,
f. if repairs or modifications have been executed by
an unauthorised person.
4 This guarantee complements any national/regional
law obligations of dealers or national distributors
and does not affect your statutory rights as a
customer.
3
7211 XTC manual Inside 1/12/08 12:41 Page 3
