390511
19
Verklein
Vergroot
Pagina terug
1/122
Pagina verder
English - 6
1 609 929 B76 • TMS • 30.11.00
Check for correct mains voltage: The voltage
of the power source must agree with the voltage
specified on the nameplate of the machine.
Equipment marked with 230 V can also be con-
nected to 220 V.
Switching on: Slide the On/Off switch 3
forward without exerting any
pressure.
Press the On/Off switch 3.
Switching off: Release the On/Off switch 3.
Locking: Continue to slide the
On/Off switch 3 forward whilst
depressed.
Switching off: Press and release On/Off
switch 3.
Switch configuration without lock
(specific countries):
Switching on: Slide the On/Off switch 3
forward without exerting any
pressure.
Press the On/Off switch 3.
Switching off: Release the On/Off switch 3.
Test run!
Check the grinding tool before use. The
grinding tool must be flawlessly mounted
and be able to rotate freely. Perform a test
run of at least 30 seconds without load. Do
not use damaged, out-of-round or vibrating
grinding tools.
Starting Current Limiting
(Type J)
As a result of soft starting, a 13-A fuse is
adequate.
A machine without starting current-limiter
requires a higher fuse protection.
Clamp the workpiece if it does not remain
stationary due to its own weight.
Do not load the machine so heavily that it
comes to a standstill.
Roughing and cutting discs become very
hot while working; do not touch until they
have cooled.
Rough Grinding
With an approach angle of 30° to
40°, the best roughing results can
be achieved. Move the machine
back and forth with moderate pres-
sure. In this manner, the work piece
will not become too hot, does not
discolour and no ridges are formed.
Never use a cutting disc for roughing.
Flap disc
With the flap disc (optional extra), curved sur-
faces and profiles (contour sanding) can be
worked.
Flap discs have a considerably higher service life
than sanding sheets, lower noise level and lower
sanding temperatures.
Cutting
When cutting, do not press, tilt or
oscillate. Work with moderate ad-
vancing that is adapted to the mate-
rial being worked.
Do not brake coasting cutting disks
with side pressure.
Important is the di-
rection in which cut-
ting is performed.
The machine must
always work opposite
to the direction of ro-
tation. Therefore,
never move the ma-
chine in the other di-
rection! Otherwise,
the danger exists of it
being pushed un-
controlled out of the
cut.
Cutting grinder Stand
With the cutting grinder stand (optional extra),
work pieces of the same length can be cut at an-
gles of 0 to 45°.
When cutting profiles and square pipes, it is best
to start with the smallest cross section.
For mounting the machine in the cutting stand a
cap or a claw are required, depending on the type
of cutting stand used.
Initial Operation
Operating Instructions
16 A
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch gws 23 230 js bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch gws 23 230 js in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 5,26 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info