390511
16
Verklein
Vergroot
Pagina terug
1/122
Pagina verder
English - 3
1 609 929 B76 • TMS • 30.11.00
When grinding metal, flying sparks are pro-
duced. Take care that no persons are endan-
gered. Due to danger of fire, no combustible
materials should be located in the vicinity
(spark flight zone).
Be careful when cutting grooves, e. g. in load-
carrying walls: See information on structures.
Be careful of hidden electrical lines or gas and
water pipes. Check the working area, e. g. with
a metal detector.
Blocking the cutting disc leads to jerking reac-
tion forces on the machine. In this case switch
off the machine immediately.
Pay attention to the dimensions of the grinding
disc. The mounting hole diameter must fit the
mounting flange 9 without play. Do not use re-
ducer pieces or adapters.
Never use cutting discs for rough grinding. Do
not exert any lateral pressure on the cutting
discs.
Observe the manufacturer’s instructions for
mounting and using grinding tools.
Caution! The grinding tool runs on after the
machine is switched off.
Do not clamp the machine in a vice.
Bosch is only able to ensure perfect function-
ing of the machine if the original accessories
intended for it are used.
The machine is intended for cutting, roughing and
brushing metal and stone materials without using
water. For cutting stone, a cutting guide is re-
quired.
Slots in load carrying walls are subject to the
Standard DIN 1053, Part 1 or country-specific
regulations.
These regulations are to be observed under all
circumstances. Before beginning work, consult
the responsible structural engineer, architects or
the construction supervisor.
Before any work on the machine itself, pull
the mains plug.
For work with roughing or cutting discs,
the protective guard 5 must be mounted.
Guard with locking screw
The coded projection 14 on the guard 5 ensures
that only a guard that fits the machine type can be
mounted.
Loosen the clamping screw 13, if necessary.
Place the guard 5 with coded projection 14 into
the coded groove on the spindle collar of the ma-
chine head and rotate to the required position
(working position).
The closed side of the protective guard 5
must always point to the operator.
Tighten clamping screw 13.
Guard with quick clamp
(Optional extra)
The guard is pre-adjusted to the diameter
of the spindle collar. Therefore do not
loosen or tighten the adjustment screw 7.
Open the clamping lever 8.
Place the protective guard 5 on the spindle collar
of the machine head and turn to the required po-
sition (working position).
To fasten the protective guard 5, close the clamp-
ing lever 8.
The closed side of the protective guard 5
must always point to the operator.
Auxiliary Handle
For all work with the machine, the auxiliary
handle 4 must be mounted.
Screw the auxiliary handle 4 into the head of the
machine according to the working method.
Hand Protector (Optional extra)
For work with the rubber sanding plate 19 or with
the cup brush 22/disc brush/flap disc, mounting
the hand protector 17 (optional extra) is recom-
mended. The hand protector 17 is fastened with
the auxiliary handle 4.
Intended Use
Information Structures
Mounting the
Protective Devices
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch gws 23 230 js bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch gws 23 230 js in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 5,26 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info