390388
11
Verklein
Vergroot
Pagina terug
1/13
Pagina verder
English - 7
Clamp the workpiece if it does not remain
stationary due to its own weight.
Do not strain the machine so heavily that it
comes to a standstill.
Grinding and cutting discs become very
hot while working; do not touch until they
have cooled.
Rough Grinding
The best roughing results are
achieved when setting the machine
at an angle of 30° to 40°. Move the
machine back and forth with mod-
erate pressure. In this manner, the
workpiece will not become too hot,
does not discolour and no grooves
are formed.
Never use a cutting disc for roughing.
Flap Disc
With the flap disc (accessory), curved surfaces
and profiles (contour sanding) can be worked.
Flap discs have a considerably higher service life
than sanding sheets, lower noise level and lower
sanding temperatures.
Cutting
When cutting, do not press, jam or
oscillate the machine. Work with
moderate feed, adapted to the ma-
terial being machined.
Do not reduce the speed of running
down cutting discs by applying
sideward pressure.
The direction in which
the cutting is per-
formed is important.
The machine must
always work in an
up-grinding motion.
Therefore, never
move the machine in
the other direction!
Otherwise, the dan-
ger exists of it being
pushed uncon-
trolled out of the cut.
Grinder Stand
With the grinder stand 26 (accessory), work-
pieces can be cut at angles of 0 to 45° at the
same lengths.
The safety notes and operating instructions in the
respective operating instructions manual of the
angle grinder are to be strictly observed. Use only
original Bosch grinder stands.
Cutting Stone
The machine must be used only for dry
cutting/grinding.
It is best to use a dia-
mond cutting disc. As
a safety measure
against jamming, use
the cutting guide 25
with the special dust
extraction protection
guard.
Operate the machine with dust extraction only. In
addition, wear a dust mask.
The vacuum cleaner
must be approved for
the extraction of ma-
sonry dust.
Bosch provides suita-
ble vacuum cleaners.
Switch on the ma-
chine and place the
front part of the cut-
ting guide on the
workpiece.
Slide the machine with moderate feed, adapted
to the material to be worked (Figure).
Operating Instructions
26
1 609 929 F75.book Seite 7 Dienstag, 9. März 2004 9:19 09
12 • 1 609 929 F75 • 04.03
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch gws 20 180 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch gws 20 180 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,47 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Bosch gws 20 180

Bosch gws 20 180 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanôl, Türkiye, Dansk, Svenska, Norsk, Suomi - 122 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info