391343
24
Verklein
Vergroot
Pagina terug
1/301
Pagina verder
English | 251 609 929 K94 20.12.06
Note: When not using for extended periods, pull the
mains plug out of the socket outlet. When the mains
plug is inserted and mains voltage is given, the power
tool, even when switched off, still consumes a low
amount of current.
Rough Grinding
f Never use a cutting disc for roughing.
The best roughing results are achieved when setting
the machine at an angle of 30° to 40°. Move the
machine back and forth with moderate pressure. In
this manner, the workpiece will not become too hot,
does not discolour and no grooves are formed.
Flap Disc
With the flap disc (accessory), curved surfaces and
profiles can be worked.
Flap discs have a considerably higher service life,
lower noise levels and lower sanding temperatures
than conventional sanding sheets.
Cutting Metal
f For cutting metal, always work with the pro-
tection guard for cutting 12.
When cutting, work with moderate feed, adapted to
the material being cut. Do not exert pressure onto the
cutting disc, tilt or oscillate the machine.
Do not reduce the speed of running down cutting
discs by applying sideward pressure.
The machine must
always work in an up-
grinding motion. Oth-
erwise, the danger
exists of it being
pushed uncon-
trolled out of the cut.
When cutting profiles
and square bar, it is
best to start at the
smallest cross sec-
tion.
Cutting Stone
f For cutting stone, always work with the cut-
ting guide with dust extraction protection
guard 19.
f The machine may be used only for dry cut-
ting/grinding.
For cutting stone, it is best to use a diamond cutting
disc. As a safety measure against jamming, the cutting
guide with dust extraction protection guard 19 must
be used.
Operate the machine only with dust extraction and
additionally wear a dust protection mask.
The vacuum cleaner must be approved for the extrac-
tion of masonry dust. Bosch provides suitable vacuum
cleaners.
Switch on the
machine and place
the front part of the
cutting guide on the
workpiece. Slide the
machine with moder-
ate feed, adapted to
the material to be
worked.
For cutting expecially hard material, e. g., concrete
with high pebble content, the diamond cutting disc
can overheat and become damaged as a result. This
is clearly indicated by circular sparking, rotating with
the diamond cutting disc.
In this case, interrupt the cutting process and allow
the diamond cutting disc to cool by running the
machine for a short time at maximum speed with no
load.
Noticeable decreasing work progress and circular
sparking are indications of a diamond cutting disc that
has become dull. Briefly cutting into abrasive material
(e. g. lime-sand brick) can resharpen the disc again.
Information on Structures
Slots in structural walls are subject to the Standard
DIN 1053 Part 1, or country-specific regulations.
These regulations are to be observed under all cir-
cumstances. Before beginning work, consult the
responsible structural engineer, architect or the con-
struction supervisor.
Maintenance and Service
Maintenance and Cleaning
f Before any work on the machine itself, pull
the mains plug.
f For safe and proper working, always keep
the machine and ventilation slots clean.
f In extreme working conditions, conductive
dust can accumulate in the interior of the
machine when working with metal. The pro-
tective insulation of the machine can be
degraded. The use of a stationary extraction
system is recommended in such cases as
well as frequently blowing out the ventila-
tion slots and installing a residual current
device (RCD).
OBJ_BUCH-310-001.book Page 25 Wednesday, December 20, 2006 9:31 AM
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch gws 1400 professional bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch gws 1400 professional in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 14,72 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info