388800
21
Verklein
Vergroot
Pagina terug
1/282
Pagina verder
English | 21
Bosch Power Tools 1 619 929 740 | (24.7.07)
29.06.2007, Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Assembly
f Before any work on the machine (e. g.,
maintenance, tool change, etc.) as well as
during transport and storage, set the rota-
tional direction switch to the centre posi-
tion. Unintentional actuation of the On/Off
switch can lead to injuries.
Battery Charging
A battery that is new or has not been used for a
longer period does not develop its full capacity
until after approx. 5 charging/discharging cy-
cles.
To remove the battery 11, press the battery re-
lease button 14 and pull the battery downward
out of the power tool. Do not exert any force.
(see figure A)
The battery is equipped with a NTC temperature
control which allows charging only within a tem-
perature range of between 0 °C and 45 °C. A
long battery service life is achieved in this man-
ner.
A significantly reduced working period after
charging indicates that the battery is used and
must be replaced.
Observe the notes for disposal.
Battery Charge-control Indication
The battery charge-control indicator 10 indi-
cates the charge condition of the battery 11 dur-
ing the working procedure.
Push button 9 to indicate the charge condition
when the battery is removed or when the power
tool is switched off. The battery charge-control
indicator automatically goes out after approx.
5seconds.
When the first indicator element (0
10%)
flashes, the battery is almost completely dis-
charged and must be recharged again.
Discharge the battery occasionally until the
speed of the power tool reduces significantly
and the battery charge-control indicator 10
completely goes out. Frequent charging after
short-term usage impairs the indication accura-
cy and the service life of the battery.
Auxiliary Handle
f Operate your machine only with the auxilia-
ry handle 12.
The auxiliary handle 12 can be set to any position
for a secure and low-fatigue working posture.
Turn the bottom part of the auxiliary handle 12
in counterclockwise direction and swivel the
auxiliary handle 12 to the desired position. Then
retighten the bottom part of the auxiliary handle
12 by turning in clockwise direction.
Adjusting the Drilling Depth (see figure C)
The required drilling depth X can be set with the
depth stop 13.
Press the button for the depth stop adjustment
5 and insert the depth stop into the auxiliary
handle 12.
Insert the SDS-plus drilling tool to the stop into
the SDS-plus tool holder 1. Otherwise, the mov-
ability of the SDS-plus drilling tool can lead to
incorrect adjustment of the drilling depth.
Pull out the depth stop until the distance be-
tween the tip of the drill bit and the tip of the
depth stop correspond with the desired drilling
depth X.
The knurled surface of the depth stop 13 must
face upward.
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
0 – 10 %
10 – 20 %
20 – 40 %
40 – 60 %
60 – 80 %
80 – 100 %
OBJ_BUCH-372-001.book Page 21 Tuesday, July 24, 2007 1:31 PM
21

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch gbh 24 0 vre bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch gbh 24 0 vre in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 8,29 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info