551159

Bosch WTE84106 Handleiding

2
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
7
Programme overview also see Page 5
Sort the laundry according to type of textile and fabric. Fabrics must be suitable for tumble drying.
After drying...
c
iron laundry
lightly iron laundry
@c
do not iron laundry
c
mangle laundry
PROGRAMMES TEXTILE TYPE AND INFORMATION
**L Cottons
max. 7 kg
Hard-wearing fabrics, boil-resistant fabrics made of cotton or linen.
**IEasy-Care
max. 3.5 kg Non-iron laundry made of synthetic fibres and blended fabric, easy-care cotton.
Iron Dry
c÷@c Fabrics suitable for ironing (iron fabrics in order to avoid creasing).
Cupboard Dry
@ Single-layer fabrics.
*Extra Dry
@ Fabrics made of thick, multilayered items of clothing.
ZSportswear
max. 1.5 kg
Fabrics with membrane coating, water-repellent fabrics, functional clothing, fleece fabrics (dry jackets/trousers with
removable internal lining separately).
A SuperQuick 40’
max. 2 kg
Laundry made of synthetic fibres, cotton or blended fabrics (for example) that needs to be dried quickly. The values may
differ from the those specified depending on the type of fabric, mixture of laundry to be dried, residual moisture in the
fabric and loading capacity.
Timed Programme
warm 20 min.
max. 3 kg
Pre-dried, multi-layered, sensitive fabrics made of acrylic fibres, or separate small items of laundry.
Also for subsequent drying.
*for LCottons and IEasy-Care programmes only
**Dryness levels can be selected individually aExtra Dry, Cupboard Dry and Iron Dry (depending on the model).
Degree of dryness can be finely adjusted; multi-layered textiles require a longer drying time than single-layered items of clothing.
Recommendation: Dry separately.
9306 / 9000874932
*874932*
Robert Bosch Hausgeräte GmbH
Carl-Wery-Str. 34
81739 München/Deutschland
WTE84106GB
8
Installation
– Delivery specification: dryer, instructions for installation and use, woollens basket
(depending on model).
– Check dryer for transport damage.
– The dryer is very heavy. Do not attempt to lift it on your own.
– Be careful to avoid sharp edges.
– Do not lift the dryer by any of the protruding parts (e.g. the door) as they may break off.
– Do not set up in a room that is susceptible to frost.
Freezing water may cause damage.
– If in doubt, have the appliance connected by an expert.
Setting up the dryer
– The appliance plug must always be accessible.
– Ensure that the appliance is installed on a clean, level
and solid surface.
– Keep the cooling grille at the front of the dryer
unobstructed.
– Keep the area around the dryer clean.
– Make the dryer level using the threaded feet
and a spirit level.
Do not remove the threaded feet under any
circumstances.
Mains connection see safety instructions
a
Page 11.
– Connect to an AC earthed socket. If in doubt have the socket checked by an expert.
– The mains voltage and the voltage shown on the rating plate (
a
Page 9) must correspond.
– The connected load and necessary fuse protection are specified on the rating plate.
Frost protection / Transport
Preparation
1. Empty the condensation container
a
page 4.
2. Select any programme using the programme selector.
3. Press the
Start/Stop button
a
condensation is pumped into the container.
4. Wait 5 min., and then empty the condensation container again.
5. Turn the programme selector to Off.
1.
Take all accessory parts
out of the drum.
The drum must be empty.
2.
Do not operate the dryer if
there is a danger of frost.
Do not set up the dryer behind a door or sliding
door as this may obstruct or prevent the dryer door
from opening. This will prevent a potentially fatal
danger to children from locking themselves in.
9
Technical data
ʠ
Dimensions (DxWxH) 60 x 60 x 85 cm (height adjustable)
Weight approximately 45 kg
Max. capacity 7 kg
Condensation container 4.2 l
Connection voltage
Connected load
Fuse protection see appliance rating plate
Ambient temperature
Product number/
Production number
You can find the rating plate on the back of the dryer.
ʠ
Drum interior light (depending on model) (bulb E14, 25 W)
The drum lights up after the door is opened or closed, and after the programme starts,
and switches off automatically. Changing the bulb a page 10.
Consumption rates
Fabrics/programmes
Residual moisture in the fabrics
after spinning
Drying time**
Energy
consumption**
L Cottons 7 kg
Cupboard Dry* 1400 rpm (50%) 106 min 3.60 kWh
1000 rpm (60%) 124 min 4.20 kWh
800 rpm (70%) 143 min 4.80 kWh
Iron Dry* 1400 rpm (50%) 82 min 2.59 kWh
1000 rpm (60%) 98 min 3.28 kWh
800 rpm (70%) 112 min 3.96 kWh
cEasy-Care 3.5 kg
Cupboard Dry* 800 rpm (40%) 42 min 1.35 kWh
600 rpm (50%) 51 min 1.65 kWh
* Programme setting for testing in accordance with applicable standard EN61121.
** The values may differ from those specified, depending on the type of fabric, composition of
laundry to be dried, residual moisture in the fabric and the amount of laundry being loaded.
Fabrics/programmes Drying time Annual energy consumption
L Cottons 7 kg / 3.5 kg*
Cupboard Dry*** 97 min / per cycle 504 kWh / per year
***Programme setting for testing and energy labelling in accordance with Directive 2010/30/EU.
Optional accessories (from after-sales service using order number)
Platform
For easier loading and unloading. The basket contained in the drawer can be used to carry
the laundry.
Washer-dryer stack connection set
The dryer can be placed on top of a suitable washing machine with the same width and depth
to save space. The dryer must be fastened to the washing machine using this connection set.
With pull-out worktop: WTZ 11300
Connection fittings for condensation outlet
The condensation is conveyed directly via a hose.
Installation underneath the worktop
Instead of the appliance covering plate, you must have a metal cover fitted by
a specialist.
WMZ
20500
WTZ
11310
WTZ
1110
WTZ
10290
10
What to do if ...
If you cannot rectify a fault yourself (e.g. switching off/on), please contact our after-sales
service. We will always find an appropriate solution and will avoid unnecessary visits by
engineers. Trust the expertise of the manufacturer and rest assured that the repair will be
carried out by trained service technicians using original spare parts. The contact details of your
local after-sales service can be found in the enclosed
after-sales service directory, or by
calling one of these numbers:
– GB 0844 8928979 (Calls from a BT landline will be charged at up to 3 pence per minute.
A call set-up fee of up to 6 pence may apply.)
– IE 01450 2655 (0.03 € per minute at peak. Off peak 0.0088 € per minute.)
When contacting the after-sales service, please quote the appliance's product number (E no.)
and production number (FD) (see the inside of the door).
Set the programme selector to
Off and remove the appliance plug from the socket.
ʠ
The Start/Stop indicator lamp
does not light up.
Mains plug plugged in? Programme selected?
Check the socket fuse.
ʠ
The display panel light and
indicator lights (depending on
model) go out and the
Start/
Stop indicator light flashes.
Energy-saving mode is activated
a
see the separate Energy-saving mode instructions.
ʠ
The Container and
Start/Stop indicator lights are
flashing.
Empty the condensation container.
If featured, check hose for condensation outlet.
ʠ
The Clean and Start/Stop
indicator lights are flashing.
Clean the fluff filter and/or air cooler under running water
a
Page 4/6.
ʠ
Dryer does not start.
Start/Stop button selected?
Door closed?
Programme set?
Ambient temperature greater than 5 °C?
ʠ
Water is running out. Align dryer horizontally.
Clean air cooler seal.
ʠ
The door opens by itself. Push the door closed until you hear it engage.
ʠ
Creasing. Laundry load exceeded?
Remove articles of clothing immediately after
the end of the programme, hang up and pull into shape.
Unsuitable programme selected a Page 7.
ʠ
Drying result is not satisfactory
(laundry feels too damp).
Warm laundry feels damper than it actually is.
The selected programme does not suit the load. Use another
drying programme or, in addition, select the time programme a
Page 7.
Use fine adjustment for the drying result a Page 5/6.
Fine layer of limescale on the humidity sensors
a Clean the humidity sensors a Page 6.
Programme termination, e.g. tank full, mains power supply failure,
door open or maximum drying time reached.
ʠ
Drying time too long. Rinse the fluff filters under running water a Page 4.
Insufficient supply of air a ensure that air can circulate.
Air inlet possibly blocked a Clear inlet a Page 8.
Ambient temperature higher than 35 °C a ventilate the room.
ʠ
The humidity in the room
increases significantly.
Make sure the room is sufficiently ventilated.
ʠ
Mains failure. Remove laundry from the dryer immediately and spread out.
This allows the heat to dissipate.
ʠ
One or more indicator lights for
programme status are flashing.
Clean filter and air cooler
a
Page 4/6.
Check installation conditions
a
Page 8.
Switch off, leave to cool down, switch on again, restart
programme.
ʠ
The interior light is not working
(depending on model).
Pull out the appliance plug, remove the cover cap in the interior
above the door (use Torx 20 screw driver) and replace
the bulb. Close the cover cap.
Never operate the dryer without a cover cap.
11
Safety instructions
Emergency
– Pull the appliance plug out of the socket immediately or disconnect the fuse.
ONLY use the
dryer...
– in rooms inside the house.
– to dry fabrics.
The dryer must
NEVER...
– be used for other purposes than those described above.
– be modified in terms of its technology or attributes.
Dangers
– The dryer must not be used by children or persons who have not been
instructed in its use.
– Do not leave children unsupervised near the dryer.
– Keep pets away from the dryer.
– Remove all objects from pockets.
Make especially sure that cigarette lighters are removed as they constitute
an
a
explosion hazard.
– Do not lean or sit on the door
a
risk of tipping.
Installation
– Secure loose cables
a
tripping hazard.
– Do not operate the dryer if there is a risk of frost.
Mains
connection
– Connect the dryer according to specifications to an AC earthed socket, as
otherwise it cannot be guaranteed that the appliance is completely safe.
– The cable cross-section must be sufficient.
– Only use earth-leakage circuit breakers with the following symbol:
– The appliance plug and socket must be compatible.
– Do not use multiple plugs/couplings and/or extension cables.
– Do not hold the appliance plug with wet hands
a
risk of electric shock.
– Never pull the appliance plug out of the socket by its cable.
– Do not damage the mains lead
a
risk of electric shock.
Operation
– Only load the drum with laundry.
Check the contents before you switch the dryer on.
– Do not use the dryer if the laundry has been in contact with solvents, oil, wax,
grease or paint (e.g. hair setting spray, nail polish remover, stain remover,
cleaning solvent, etc.)
a
fire/explosion hazard.
– Dust (e.g. coal dust, flour) poses a danger: do not use the dryer
a
explosion hazard.
– Do not put laundry containing foamed material/rubber in the dryer
a
elastic
material may be destroyed and the dryer may be damaged due to possible
deformation of the foamed material.
– Switch off the dryer once the programme has ended.
– Condensation is not drinking water and may be contaminated with fluff.
Defect
– Do not use the dryer if it is defective or if you suspect it is.
Repairs must only be carried out by the after-sales service.
– Do not use the dryer if the mains cable is defective. To avoid danger, only
have the defective mains cable replaced by the after-sales service.
– Always pull the mains plug out of the socket before changing the bulb for the
interior light
a
risk of electric shock.
Spare parts
– Only use genuine spare parts and accessories for safety reasons.
Disposal
– Dryer: pull out the appliance plug, then cut off the mains cable from
the appliance.
Dispose of at municipal waste disposal facility.
– Packaging: do not leave children alone with packing parts
a
risk of suffocation.
– All materials are environmentally sound and can be reused. Dispose of in
an environmentally-responsible manner.
Dryer
en Instruction manual
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch WTE84106 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch WTE84106 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,75 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info