697111
9
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
A fault, what to do?
9
6 720 876 024 (2018/09)
3 A fault, what to do?
CAUTION:
Attention!
Repairs must only be carried out by an authorised technician.
Improper repairs can lead to risk of serious injury to the user.
If your appliance does not operate as required, it is often due to a very
minor problem. Please check whether you can remedy the fault yourself
by using the following guidelines. You will save yourself the costs of an
unnecessary visit by customer service personnel.
3.1 Faults that the customer can troubleshoot himself
If the fault could not be eliminated, please call customer service.
3.2 Faults that the customer service specialist should troubleshoot
3.3 Faults that are automatically remedied
4 Guarantee
The guarantee conditions for this appliance are as defined by our
representative in the country in which it is sold.
Details regarding these conditions can be obtained from the dealer from
whom the appliance was purchased. The bill of sale or receipt must
be produced when making any claim under the terms of this guarantee.
Subject to change without notice.
Fault Cause Solution
Water flow-rate is too low. The filter in either the water tap or the
showerhead is clogged.
Remove the filter and either clean it or descale it.
A high water temperature is set, but it is not
reached.
The continuous-flow heater is connected to a
thermostatically-controlled water tap.
Set the temperature on the continuous-flow
heater to „60 °C“.
The display is blank. The fuse in the fusebox has tripped/blown. Check the fuse in the fusebox.
The water is not warm. The supply temperature has reduced. Reduce the water flow on the taps until the
desired water temperature is reached.
The temperature of the water leaving the tap is
higher than the set temperature.
The temperature of the water supplying the
continuous-flow heater is higher than the set
temperature (e. g. due to pre-warmed water
supplied from a solar water heater).
The thermostatic premixer in the domestic
supply must be set accordingly to lower
temperatures.
“°C” flashes in the display. The power limit has been reached. Reduce the water flow at the tap or lower the
temperature setting on the appliance.
Fault Cause Solution
Water flow-rate is too low despite cleaning of
filter using the water tap or showerhead.
A filter in the appliance is clogged. Get a servicing expert to clean the appliance.
The display is blank despite fault-free function of
the mains electricity supply fuses.
There is a fault in the appliance. Get a servicing expert to check the appliance.
The display shows the error code “E..”. There is a fault in the appliance. Get a servicing expert to check the appliance.
Fault Cause Solution
The display shows “00,0°C”. The air sensor in the appliance detects air in the
water and momentarily switches the heating
element off.
After a few seconds, the continuous-flow heater
automatically goes back into operation.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch Tronic 7000 - 24-27 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch Tronic 7000 - 24-27 in de taal/talen: Nederlands, Duits, Engels, Frans, Pools, Turks als bijlage per email.

De handleiding is 2,83 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info