780662
11
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
For technicians only
11
TR5500T – 6 720 875 994 (2018/01)
heating” lights up. The function turns itself off again
automatically as soon as the configured temperature has been reached.
The LED “fast-heating” turns off.
The rest of the time, the device does not heat. If the “fast-heating”
button is activated, the device heats once to the configured
temperature. Afterwards, the device turns itself off automatically.
Boiler Mode
Connection without off-peak contact.
The device does not heat by default.
If the “fast-heating” button is activated, the device heats once
to the configured temperature. Afterwards, the device turns itself off
automatically.
Each further heating process must be started by pushing the button
“fast-heating” .
Electrical Connections
WARNING:
Danger of electric shock!
The power switch “S1” may only be activated in an unpowered state!
Remove lower cap by taking the screws out (Diagram 15, 15.1, 15.2,
15.3).
Lead cable through the cable gland and cord grip and connect,
then tighten the cable gland and cord grip (Diagrams 12- 13).
Check that the system is suitable for the maximum power absorbed
by the water heater (please refer to the data plate) and that the cross-
section of the electrical connection cables is suitable, and no less
than 1.5 mm2.
Operating mode
Set the power switch “S1” to the correct operating mode on
the electronic board.
Set the desired load according to the connection examples.
The power switch is set by the manufacturer in position 5.
Double power
Depending on the home installation, the following connection variations
are possible:
Refer to the connection types recommended for double power
Variant A, (Diagram 15):
If no low-tariff electricity is to be used, do not remove bridge between L1
and L1T.
Variant B, (Diagram 15.1)
Connect the output of the autotimer (delivered by the electricity
provider) with L1 and L1T.
Variant C, (Diagram 15.2)
Connect switched phase L1T (connection for low-tariff power) to L1T
terminal.
Variant D, (Diagram 15.3)
Connect switched phase L1 to terminal L1 and L1T.
Single power
Depending on the home installation, the following connection variations
are possible:
Refer to the connection types recommended for single power
Set power switch “S1” on the electronic board to positions 1 / 2 / 3 / 4
“single power”.
Boiler mode
Depending on the home installation, the following connection variations
are possible:
Refer to the connection types recommended for boiler switch.
Set power switch “S1” on the electronic board to positions 8 / 9 / 0
“boiler mode”.
Finally, separate the appropriate circuit diagram (E1/E2) and the
corresponding power-switch position “S1” from the enclosed adhesive
foil and adhere to the pad provided. Fill out the information decal about
the installed circuit and installed load and adhere to the outside of
the cover.
Initial Use
WARNING:
Important!
Fill the reservoir and flush it out until water discharges from all hot water
taps, otherwise the temperature sensor and retainer will be damaged
and require replacing.
Power Switch “S1” Mode of Operation
Double power switch positions 5 / 6 / 7
Single power switch positions 1 / 2 / 3 / 4
Boiler mode switch positions 8 / 9 / 0
According to the duration of the off-peak period of either 8 or 4 hours, and the associated loads
(refer to connection types), set the power switch “S1” to the correct positions 5 / 6 / 7,
of the double power set-up.
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch Tronic 5500T bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch Tronic 5500T in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 3.41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info