112553
14
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
14
Cleaning and maintenance
There are two guides on the head: front and
back.
First fit the rear cord and then the front cord
into the guides on the collar and secure.
Fig. 23.
The ironing dummy is joined to each airbag
via an interior cord.
Once the inner airbags have been fitted,
turn the sleeves of the ironing dummy
inside out. Fig. 24.
Then close the snap fasteners joining the
two parts and turn the sleeve (currently
inside out) outside out again. The arms of
the airbags are now inside the ironing
dummy arms. Fig. 25.
Fit the lower adjustment cord on the ironing
dummy into the guide. Make sure that it is
secured properly. Fig. 26.
On the front, the adjustment cord has to be
fitted under the 2 supports on the appliance
on the rear of the button band. Fig. 27.
Tighten the fixture fitting for this cord.
The fixture fitting has to be positioned into
the central rear groove, Fig. 26. Then pull
the adjustment cord again.
Check that all of the adjustment cords are
secured properly.
Close the button band. It clicks into position.
Check that the ironing dummy works properly:
Start the “ cold” programme. The
programme can be stopped at any time by
pressing the “start/stop” button.
Check that the ironing dummy is fitted
properly.
Tighten any slack cords if necessary.
Correct any problems.
Fit the head section into the front guide.
Click the front hook into the hole on the top
part of the head.
Press the head section until it clicks into
position. Fig. 28.
Position each of the cuff adjusters and close
the relevant snap fasteners.
Be particularly careful when fitting the
ironing dummy and follow all the
instructions given.
The ironing dummy should only be fitted
when dry.
First fit the airbags:
Each of the airbags (symmetrical) is joined
with a strip. This strip is fitted on the front
between the button band and the support
tubes. The airbag with an extra section with
2 snap fasteners in the middle must be
fitted on the left-hand side of the appliance
(looking head on).
There are three snap fasteners on each
side of the shoulder area which are fitted to
the relevant airbag.
Fit the adjustment cords onto the round
guides around the air-output grille and
secure the cord fixture. Fig. 21.
Position the cross formation on the airbags
and close the snap fasteners on the front at
the bottom. Fig. 22.
The extra section on the bottom left-hand
side must be wrapped around the left-hand
tube, protecting the hole on the tube in this
area.
Check that the adjustment cords are
secured properly.
Check that the airbags are positioned
properly.
Start the “ cold” programme. The
programme can be stopped at any time by
pressing the “start/stop” button.
Check that the airbags are positioned
properly.
Tighten any slack cords.
Correct any problems.
Fit the ironing dummy onto the upper part of
the appliance with the button band still
unlocked and the knob in its vertical
position.
Fit the ironing dummy from back to front.
There are 4 holes on the front of the upper
part of the ironing dummy. The front
adjustment cords are on this section.
When the dummy is fitted, set the knob to
horizontal.
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch THB 1500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch THB 1500 in de taal/talen: Nederlands, Duits, Engels als bijlage per email.

De handleiding is 2,25 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info