en
Storing the appliance (D)
1. Always allow the appliance to cool down before
storing it.
2. Set the switches for main power and steam boiler to
the “Off/Stop” position and disconnect the connec-
-
tion.
3. Place the iron on the iron pad, standing on the
soleplate.
4. Empty the water tank and store the mains cable on
the cord rewind facility. Tidy the steam hose on the
handle of the iron using the cord clip provided (14). Do
not wrap the cords too tight.
“Calc‘n clean” (E)
Cleaning the Boiler
To extend the life of your steam generator and to avoid
any build up of scale, it is essential that you rinse out
the boiler after several hours of use. If the water is hard,
increase the frequency.
Approximately after 50 hours of use, "Calc´n clean" pilot
light (9) will light up indicating that boiler must be rinsed.
Do not use descaling agents for rinsing out the boiler, as
they could damage it.
1. Check that the appliance is cold and unplugged for
more than 2 hours, and that the removable water tank
(1) is empty.
2. Place your appliance on the edge of your kitchen
sink.
3. Remove the plastic cover located on the bottom of the
appliance by turning it to the position.
4. Unscrew the boiler drainage plug located on the
bottom of the appliance using a coin.
5. Holding your steam generator in upside down position,
and using a jug, fill the boiler (in the base unit) with 1/4
litre of water
6. Shake the base unit for a few moments and then
empty it completely over a sink or bucket. To obtain
the best result, we recommend that this operation is
done twice
Important: before re-closing, make sure no water
remains in the boiler.
7. Replace and tighten up the boiler drainage plug with a
coin.
8. Insert and close the plastic cover by turning it to the
position.
To reset "Calc´n clean" pilot light and hours counter,
switch the station off twice, keeping it off during at least
30 seconds each time
Fabric protection soleplate
cover (F)
(depending on the model)
The fabric-protection soleplate cover is used for steam-
ironing delicate garments at maximum temperature
without damaging them. Use of the soleplate cover also
does away with the need for a cloth to prevent shine on
dark materials.
It is advisable to first iron a small section on the inside of
the garment to see if it is suitable.
To attach the soleplate cover to the iron, place the tip
of the iron into the end of the soleplate cover and pull
the elastic strap over the lower rear of the iron until it
fits tightly. To release the soleplate cover, pull the elastic
strap and remove the iron.
The fabric-protection soleplate cover may be purchased
from the customer service or specialist shops:
Accessory code
(After-sales)
Name of accessory
(Specialist outlets)
464846 TDZ2510
464745* TDZ2520*
* Cork handle iron
Trouble shooting
Problem Possible causes Solution
The steam generator
does not come on.
• There is a connection problem.
• The steam tank and/or main power button
is not switched on.
• Check the mains cable, the plug and the
socket.
• Press the buttons for main power (8) and
steam generator (4) “Start/I”.
The iron does not
heat up.
• The main power button is not switched on.
• The temperature control knob is set to the
“min” position.
• Press the main power button (8) “I”.
• Set the temperature control knob (15) to
the desired position.
The iron begins
to smoke when
switched on.
• During first use: Certain components on
the appliance have been lightly greased
at the factory and may produce a little
smoke when initially heated.
• During later use: the soleplate may be
soiled.
• This is completely normal and will stop after
a short while.
• Clean the soleplate according to the
cleaning instructions in this manual.
