458026
11
Verklein
Vergroot
Pagina terug
1/68
Pagina verder
11
TA 211 E
English
4 Mounting
Before starting work, the voltage supply
(230 V, 50 Hz) to the boiler must be dis-
connected.
4.1 Mounting of the Outdoor Tempera-
ture Sensor AF (Figures and )
The outside temperature sensor AF is intend-
ed for mounting on the surface of an outer
wall.
The following aspects should be observed:
Between the Northeast and Northwest
sides of the house
A minimum of 2 m over ground level
• It should not be influenced by windows,
doors, chimneys, direct sunlight or similar
effects (Fig. ).
In recesses or under balcony and roof over-
hangs are not suitable as mounting loca-
tions (Fig. ).
If the major occupied rooms of the building
are all located in the same direction, the out-
door sensor can point in that direction.
Notes:
If the outdoor sensor is mounted on an east
wall, the sensor must be shadowed in the
early morning hours (e. g., by a neighbour-
ing house of a balcony).
Reason: The morning sun disturbs the
heating up of the house after the end of the
reduced night program.
If the major occupied rooms point in two ad-
jacent directions, mount the outdoor sensor
on the side of the house that has the worst
climatic conditions.
For the mounting height, the (vertical) cen-
tre of the height heated by the boiler has
proven to the most suitable (H/2 in Fig. ).
To mount, remove the cover (AF
c
with AF
b
)
and attach the sensor housing (AF
a
) with two
screws to the outer wall (Fig. ).
Legend for Figure :
Y/H = Occupied height to be controlled by the
sensor.
= Recommended mounting location
= Alternative mounting location
4.2 Mounting the Regulator (Figures
and )
Pull out the cover (f) at the bottom and re-
move (Fig. ).
Unscrew the screw (g, Fig. ).
Remove the cover (h) forwards.
Pull the blank panel (i) downward and re-
move (Fig. ).
Insert the TA 211 E from below into the
guide rails and slide up until it clicks
(Fig. ).
Insert the plug (k) attached to the regulator
into the intended connector (Fig. ).
4.3 Mounting the Accessories
Mount the time switch, and the mechanical
limiter in accordance with the associated in-
stallation instructions.
5 Electrical Connection
The electrical connection of the regulator has
already been described in Section 4.2.
The following conductor cross sections are to
be used:
Taking the applicable regulations into consid-
eration, the electrical cable used for the con-
nection of the outdoor sensor and the remote
control must be at least type H 05 VV-...
All 24 V lines (measurement current) must be
laid separately from lines carrying 230 V or
400 V so that no inductive effects take place
(Minimum distance 100 mm).
If external inductive influences such as those
caused by power cables, tram lines, trans-
former stations, radio and television equip-
ment, amateur radio stations, microwave
equipment or similar are to be expected,
shielded cable should used for the signal
lines.
3 5
5
5
5
3
5
From TA 211 E to the outdoor sensor:
Length to 20 m 0.75 mm
2
to 1.5 mm
2
Length to 30 m 1.0 mm
2
to 1.5 mm
2
Length over 30 m 1.5 mm
2
From TA 211 E to the remote control
(not in UK): 1.5 mm
2
11
15
11
12
13
14
15
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch TA 211E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch TA 211E in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens als bijlage per email.

De handleiding is 0,65 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info