79294
28
Verklein
Vergroot
Pagina terug
1/166
Pagina verder
28 | English
1 609 929 R16 | (14.2.08) Bosch Power Tools
Rough Grinding
f Never use a cutting disc for roughing.
The best roughing results are achieved when
setting the machine at an angle of 30° to 40°.
Move the machine back and forth with moderate
pressure. In this manner, the workpiece will not
become too hot, does not discolour and no
grooves are formed.
Flap Disc
With the flap disc (accessory), curved surfaces
and profiles can be worked.
Flap discs have a considerably higher service
life, lower noise levels and lower sanding tem-
peratures than conventional sanding sheets.
Cutting Metal
f For cutting metal, always work with the pro-
tection guard for cutting 7.
When cutting, work with moderate feed, adapt-
ed to the material being cut. Do not exert pres-
sure onto the cutting disc, tilt or oscillate the
machine.
Do not reduce the speed of running down cut-
ting discs by applying sideward pressure.
The machine must
always work in an
up-grinding mo-
tion. Otherwise,
the danger exists
of it being pushed
uncontrolled out
of the cut.
When cutting profiles and square bar, it is best
to start at the smallest cross section.
Cutting Stone
f For cutting stone, always work with the cut-
ting guide with dust extraction protection
guard 16.
f The machine may be used only for dry cut-
ting/grinding.
For cutting stone, it is best to use a diamond
cutting disc. As a safety measure against jam-
ming, the cutting guide with dust extraction pro-
tection guard 16 must be used.
Operate the machine only with dust extraction
and additionally wear a dust protection mask.
The vacuum cleaner must be approved for the
extraction of masonry dust. Bosch provides suit-
able vacuum cleaners.
Switch on the ma-
chine and place
the front part of
the cutting guide
on the workpiece.
Slide the machine
with moderate
feed, adapted to
the material to be
worked.
For cutting expecially hard material, e. g., con-
crete with high pebble content, the diamond
cutting disc can overheat and become damaged
as a result. This is clearly indicated by circular
sparking, rotating with the diamond cutting
disc.
In this case, interrupt the cutting process and al-
low the diamond cutting disc to cool by running
the machine for a short time at maximum speed
with no load.
Noticeable decreasing work progress and circu-
lar sparking are indications of a diamond cutting
disc that has become dull. Briefly cutting into
abrasive material (e. g. lime-sand brick) can re-
sharpen the disc again.
Information on Structures
Slots in structural walls are subject to the
Standard DIN 1053 Part 1, or country-specific
regulations.
These regulations are to be observed under all
circumstances. Before beginning work, consult
the responsible structural engineer, architect or
the construction supervisor.
OBJ_BUCH-393-003.book Page 28 Thursday, February 14, 2008 3:56 PM
28

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Bosch-PWS-720-115

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch PWS 720-115 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch PWS 720-115 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 6,86 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Bosch PWS 720-115

Bosch PWS 720-115 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanôl, Türkiye, Dansk, Svenska, Norsk, Suomi - 167 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info