777050
11
Verklein
Vergroot
Pagina terug
1/55
Pagina verder
English | 11
To open the battery compartment cover(6), press the lock-
ing mechanism(7) and lift open the battery compartment
cover. Insert the batteries/rechargeable batteries.
When inserting the batteries, ensure the polarity is correct
according to the representation on the inside of the battery
compartment cover(6).
Always replace all the batteries at the same time. Only use
batteries from the same manufacturer and which have the
same capacity.
uTake the batteries out of the measuring tool when you
are not using it for a prolonged period of time. The bat-
teries can corrode and self-discharge during prolonged
storage.
Operation
Start-up
uProtect the measuring tool from moisture and direct
sunlight.
uDo not expose the measuring tool to any extreme tem-
peratures or variations in temperature. For example,
do not leave it in a car for extended periods of time. In
case of large variations in temperature, allow the measur-
ing tool to adjust to the ambient temperature before put-
ting it into operation. The precision of the measuring tool
may be compromised if exposed to extreme temperat-
ures or variations in temperature.
uAvoid substantial knocks to the measuring tool and
avoid dropping it. Damaging the measuring tool can
cause accuracy to be compromised. If the laser line is
subjected to a substantial knock or is dropped, check it
by comparing it to a known horizontal or vertical refer-
ence line.
uSwitch the measuring tool off when transporting it.
The pendulum unit is locked when the tool is switched off,
as it can otherwise be damaged by big movements.
Switching On/Off
To switch on the measuring tool, slide the on/off switch (2)
to the "On" position. As soon as it is switched on, the meas-
uring tool emits laser lines from the outlet apertures(1).
uDo not direct the laser beam at persons or animals and
do not stare into the laser beam yourself (even from a
distance).
To switch off the measuring tool, slide the on/off switch (2)
to the "Off" position. The pendulum unit is locked when the
tool is switched off.
uNever leave the measuring tool unattended when
switched on, and ensure the measuring tool is
switched off after use. Others may be blinded by the
laser beam.
Operating Modes
Once the measuring tool has been switched on, it is in cross-
line operation with automatic levelling.
To change the operating mode, press the Modebutton for
laser operating mode (9) until the required laser operating
mode is displayed by the corresponding "Laser operating
mode" indicator(11) lighting up.
You can choose between the following operating modes:
Indicator Operating mode
Cross-line operation (see figuresA, B
andE): The measuring tool generates a ho-
rizontal laser plane (360° surrounding
laser line) and a vertical laser line.
Horizontal operation (see figureC): The
measuring tool generates a horizontal laser
plane.
Vertical operation (see figureD): The
measuring tool generates a vertical laser
line.
All operating modes can be selected with or without auto-
matic levelling.
Automatic Levelling
Working with automatic levelling (see figuresF–G)
When working with automatic levelling, the "Working without
automatic levelling" indicator(12) must not be lit. If neces-
sary, switch automatic levelling on again by pressing the
Lockbutton for switching off automatic levelling (8) so that
the "Working without automatic levelling" indicator goes out.
Position the measuring tool on a level, firm surface or attach
it to the holder(13) or the tripod(18).
The automatic levelling function automatically compensates
irregularities within the self-levelling range of ±4°. The level-
ling is finished as soon as the laser lines stop moving.
If automatic levelling is not possible, e.g. because the sur-
face on which the measuring tool stands deviates by more
than 4° from the horizontal plane, the levelling warning(10)
lights up red and the laser is switched off automatically.
If this is the case, set up the measuring tool in a level position
and wait for the self-levelling to take place. As soon as the
measuring tool is within the self-levelling range of ±4° again,
the levelling warning(10) goes out and the laser is switched
on.
It is not possible to work with automatic levelling outside the
self-levelling range of ±4°, as the laser line cannot be guaran-
teed to be perpendicular outside this range.
In case of ground vibrations or position changes during oper-
ation, the measuring tool is automatically levelled again.
Upon re-levelling, check the position of the horizontal or ver-
tical laser line with regard to the reference points to avoid er-
rors by moving the measuring tool.
Working without automatic levelling (see figureE)
To work without automatic levelling, press the Lockbutton
for switching off automatic levelling(8). The "Working
without automatic levelling" indicator(12) lights up red
when automatic levelling is switched off.
If you switch off the automatic levelling system, you can hold
the measuring tool freely in your hand or set it down on a
Bosch Power Tools 1 609 92A 4J0 | (25.01.2019)
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch PLL 360 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch PLL 360 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 7.28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info