708152
18
Verklein
Vergroot
Pagina terug
1/112
Pagina verder
18 | English
1 609 92A 1LU | (23.5.18)
Bosch Power Tools
Pull out the depth stop until the distance between the tip of
the drill bit and the tip of the depth stop correspond with
the desired drilling depth X.
Selecting Drill Chucks and Tools
For hammer drilling and chiselling, SDS-plus tools are re-
quired that are inserted in the SDS-plus drill chuck.
For drilling without impact in wood, metal, ceramic and plas-
tic as well as for screwdriving, tools without SDS-plus are
used (e.g., drills with cylindrical shank). For these tools, a
keyless chuck or a key type drill chuck are required.
PBH 3000-2 FRE: The SDS-plus quick change chuck
2
can easily
be replaced against the quick change keyless chuck
1
provided.
Replacing the Drill Chuck
(PBH 2800 RE/PBH 2900RE/PBH 2900 FRE/
PBH 3000 FRE Set)
To work with drilling tools without SDS-plus (e. g., drill bits
with cylindrical shank), the key type drill chuck or the keyless
chuck must be mounted.
Mounting the Key Type Drill Chuck (Accessory)
(PBH 2800 RE/PBH 2900 RE) (see figure C)
Screw the SDS-plus adapter shank 22 into a key type drill
chuck 21. Secure the key type drill chuck 21 with the se-
curing screw 20. Please observe that the securing
screw has a left-hand thread.
Inserting the Key Type Drill Chuck or the Keyless Chuck
(see figure D)
Clean the shank end of the adapter shank and apply a light
coat of grease.
Insert the key type drill chuck 21 or the keyless chuck 23
with the adapter shank into the tool holder with a turning
motion until it automatically locks.
Check the locking effect by pulling the key type drill chuck
or the keyless chuck.
Removing the Key Type Drill Chuck or the Keyless Chuck
Push the locking sleeve 5 toward the rear and pull out the
key type drill chuck 21 or the keyless chuck 23.
Removing/Inserting the Quick Change Chuck
(PBH 3000-2 FRE)
Removing the Quick Change Chuck (see figure E)
Grasp the lock ring of the quick change chuck 6 and pull it
firmly in the direction of the arrow. The quick change chuck
is released and can be removed toward the front.
After removing, protect the replacement chuck against
contamination.
Inserting the Quick Change Chuck (see figure F)
Before inserting, clean the quick change chuck and apply a
light coat of grease to the shank end.
Grasp the SDS-plus quick change chuck 2 or the quick
change keyless chuck 1 completely with your hand. Slide
the quick change chuck with a turning motion onto the drill
chuck mounting 24 until a distinct latching noise is heard.
The quick change chuck is automatically locked. Check the
locking effect by pulling the quick change chuck.
Changing the Tool
The dust protection cap 4 largely prevents the entry of drilling
dust into the tool holder during operation. When inserting the
tool, take care that the dust protection cap 4 is not damaged.
A damaged dust protection cap should be changed im-
mediately. We recommend having this carried out by
an after-sales service.
Inserting SDS-plus Drilling Tools (see figure G)
The SDS-plus drill chuck allows for simple and convenient
changing of drilling tools without the use of additional tools.
PBH 3000-2 FRE: Insert the SDS-plus quick change chuck
2
.
Clean and lightly grease the shank end of the tool.
Insert the tool in a twisting manner into the tool holder until
it latches itself.
Check the latching by pulling the tool.
As a requirement of the system, the SDS-plus drilling tool can
move freely. This causes a certain radial run-out at no-load,
which has no effect on the accuracy of the drill hole, as the
drill bit centres itself upon drilling.
Removing SDS-plus Drilling Tools (see figure H)
Push back the locking sleeve 5 and remove the tool.
Inserting Drilling Tools without SDS-plus into the Key
Type Drill Chuck (PBH 2800 RE/PBH 2900 RE)
Note: Do not use tools without SDS-plus for hammer drilling
or chiselling! Tools without SDS-plus and their drill chucks are
damaged by hammer drilling or chiselling.
Insert the key type drill chuck 21.
Open the key type drill chuck 21 by turning until the tool
can be inserted. Insert the tool.
Insert the chuck key into the corresponding holes of the
key type drill chuck 21 and clamp the tool uniformly.
Turn the mode selector switch 12 to the “drilling” position.
Removing Drilling Tools without SDS-plus from the Key
Type Drill Chuck (PBH 2800 RE/PBH 2900 RE)
Turn the sleeve of the key type drill chuck 21 with the drill
chuck key in anticlockwise direction until the drilling tool
can be removed.
Inserting Drilling Tools without SDS-plus into the Keyless
Chuck
(PBH 2900 FRE/PBH 3000 FRE Set/PBH 3000-2 FRE)
(see figure I)
Note: Do not use tools without SDS-plus for hammer drilling
or chiselling! Tools without SDS-plus and their drill chucks are
damaged by hammer drilling or chiselling.
PBH 2900 FRE/PBH 3000 FRE Set: Insert the keyless
chuck 23.
PBH 3000-2 FRE: Insert the quick change keyless chuck
1
.
Hold the rear sleeve 26 of the keyless chuck 23 and turn
the front sleeve 25 in anticlockwise direction until until the
tool can be inserted. Insert the tool.
Tightly hold the rear sleeve of the keyless chuck 23 and
firmly turn the front sleeve clockwise by hand until the
locking action is no longer heard. This automatically locks
the drill chuck.
Check the tight seating by pulling the tool.
OBJ_BUCH-318-007.book Page 18 Tuesday, November 10, 2015 5:05 PM
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch PBH 3000 FRE Set bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch PBH 3000 FRE Set in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 6,86 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info