Handleiding Bosch Indego 1200 Connect (pagina 37 van 466) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins)

591351

Verklein

Vergroot

Pagina terug

1/466

Pagina verder

English | 37

Bosch Power Tools F 016 L81 115 | (7.10.14)

Lawn Preparation

Remove stones, loose pieces of wood, wire, live mains cables

and other foreign objects from the cutting area.

Make sure that the cutting area is even and has no ditches,

grooves and steep slopes above 20° that are clear obstruc-

tions for the machine.

Cut the main area of the lawn with a conventional mower to a

max. height of 40 mm and the perimeter wire area to a max.

height of 20 mm.

Installation

For a video guide on how to install the Indego please visit

www.bosch-indego.com or use the following QR-Code.

Select a position for the docking station, horizontally levelled

and out of direct sunlight.

Note: The docking station must be positioned on the wire at

an outer edge of the cutting area. It cannot be positioned by

the side of a shed or workshop that appears as an island with-

in the cutting area.

Make sure that the docking station is placed beside the cut-

ting area with a straight 1.5 m track in front of the docking sta-

tion and a straight 1 m track behind. Whilst stood in the grass

area to be cut it is important that the docking station charging

pins point to the left. (see figure 2)

Note: If the docking station is positioned with the charging

pins pointing either into the grass area or pointing to the right

the Indego will not run correctly.

Pull the wire end through the front hole of the base plate and

straight through the wire duct and the rear hole. Fix the wire

with a peg inline with the hole. Cut off insulation carefully and

connect the wire to the right hand (red) terminal. (see

figures 4– 5)

Fix the docking station with 4 supplied fixing pins to the

ground. (see figure 6)

Lay out the perimeter wire anti-clockwise and flush to the

ground. Observe the minimum distances from lawn edges,

steps, walls, ponds, etc. Use the spacing guide. (see figure 7)

Note: The cable should be positioned so that the Indego will

not be more than 16 m away at anytime.

If the working area borders against a flat path or surface that

is level with the lawn the Indego will be able to run over it. In

such cases the perimeter wire should be positioned right up

to the edge of the lawn.

Note: Perimeter wire can be buried up

to a maximum depth of 5 cm. It is recommended to mark out

permanent objects within the garden. This will prevent the In-

dego colliding with the object and reduce wear on the shell.

Objects on the lawn below 6 cm height e.g. trees, ponds, flow-

er beds etc. must be delimited in a clockwise direction. The

lines to and from these zones may not cross but the wire

should be touching. (see figure 7)

Note: Approximately 20 cm of lawn

around the fixed object and around the

edge of the lawn will not be mown.

Fix the wire with the first peg next to the docking station, ten-

sion and fix with pegs at a distance of approx. 50 cm. (see

figure 7)

Continue the loop and bring the wire to the back of the dock-

ing station and inline with the other end of the wire. Fix the

second end of the wire also with the peg. Perimeter wire and

peg should be installed inline. Shorten the wire, cut off insula-

tion carefully and connect the wire to the left hand (black) ter-

minal. (see figure 10)

Clip on the protective cover of the docking station. (see

figure 11)

Note: If extra perimeter wire is required this can be added us-

ing one connector. (see figure 8)

The wire can be extended up to the maximum allowed length

of 450 m.

Note: If verticutting or raking is intended avoid the perimeter

wire.

Install the power supply in a cool, dry environment. Connect it

with the docking station and an indoor mains socket. (see

figure 12)

Check the indicator on the docking station (see figure 13):

–Indicator lights up continuously green, if the output volt-

age of the power supply is available and the perimeter wire

is not interrupted.

–Indicator does not light up when the output voltage of the

power supply is not available.

Installing an additional lawn

(Indego 1300)

The Indego 1300 can be used in up to three different lawns.

To install an additional cutting area/lawn you will need to have

purchased an additional docking station (F 016 800 384/

F 016 800 438) and the required perimeter wire and pegs.

To install the additional area please follow the installation in-

structions from the beginning of this section.

Plug in isolator key

14 9

Charge battery by putting the machine

into docking station 15 10

Welcome screen = Refer to manual

16 10

Lift up and carry the machine

17 11

Set height of cut

18 11

Logicut Intelligent Cutting

19 12

Cleaning

A 13

Maintenance

B 13

Action Figure Page

20-25cm

OBJ_BUCH-1573-007.book Page 37 Tuesday, October 7, 2014 12:49 PM

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Bosch Indego 1200 Connect Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Bosch Indego 1200 Connect

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info