en Cleaning function
32
1. Touch the menu field.
The list of operating modes is displayed.
2. Touch the "Cleaning" text field.
3. Touch the "Pyrolytic self-cleaning" text field.
The cleaning setting is highlighted in white on the
display.
4. Turn the rotary selector to set the cleaning setting.
The end time is calculated automatically at the same
time.
5. Press the l Start/Stop button to start.
The cooking time counts down on the display. The
heating line does not appear for the cleaning
function.
The cleaning function starts.
Ventilate the kitchen when the cleaning function is
running.
The appliance door locks shortly after the function starts
running.A message and the n symbol appear on the
display.
When the cleaning function has ended, an audible
signal sounds. The cooking time 00 m 00 s is shown on
the display. Press the ÿ On/Off button to switch off the
appliance.
The appliance door cannot be reopened until the
n symbol for the locking mechanism goes out.
Setting a later end time
You can set a later end time. Before starting the
appliance, touch the "End" text field and set a later end
time using the rotary selector.
The appliance switches to standby after it is started. The
end time can no longer be changed.
Changing and cancelling
After starting the appliance, the cleaning setting can no
longer be changed.
If you would like to cancel the cleaning function, switch
the appliance off using the ÿ On/Off button. You can
no longer pause the operation using the l Start/Stop
button.
The appliance door remains locked until the n symbol
for the locking mechanism on the display goes out.
Once the cleaning function has ended
Once the cooking compartment has cooled down, use
a damp cloth to wipe off the ash that has been left
behind in the cooking compartment, in the accessories
on the racks and around the appliance door.
Wipe the pull-out rails with a damp cloth. Then slide the
pull-out rails in and out several times. After cleaning,
some discolouration may remain on the pull-out rails.
This has no effect on performance.
Note: Very bad soiling may cause white deposits to
remain on the enamel surfaces. This is residue from the
food and is harmless. It does not affect performance.
You can remove these residues using lemon juice if
required.
Descaling
To ensure that your appliance continues to operate
correctly, it must be descaled regularly.
Descaling comprises a number of different steps. For
hygiene reasons, the descaling programme must be
run through completely before the appliance is ready
for operation again. In total, the descaling programme
runs for approx. 70–95 minutes.
■Descale (approx. 55–70 minutes), then empty and
refill the water tank
■First rinsing cycle (approx. 9–12 minutes), then
empty and refill the water tank
■Second rinsing cycle (approx. 9–12 minutes), then
empty and dry the water tank
If descaling is interrupted (e.g. due to a power failure or
because the appliance is switched off), you will be
prompted to rinse the appliance twice when you switch
it back on. The appliance cannot be used until the
second rinsing cycle has finished.
The frequency with which the appliance must be
descaled depends on the hardness of the water used.
When only another five or fewer steam-assisted
operations are possible, the appliance reminds you to
descale it with a message on the display. The number
of remaining operations is displayed after the appliance
is switched on. You can therefore prepare for the
descaling in good time.
Starting
Caution!
■Risk of damage to the appliance: Only use liquid
descalers recommended by us for the descaling
programme. The time the product needs to work
during descaling depends on the type of descaler
used. Other descalers may damage the appliance.
Descaler order no. 311 680
■Descaling solution: Do not allow any descaling
solution or descaler to come into contact with the
control panel or other surfaces on the appliance.
This damages the surfaces. If this does happen,
remove the descaling solution immediately with
water.
If you have used a steam-assisted operation
immediately before descaling, you must first switch the
appliance off so that the residual water is pumped out
of the evaporator system.
1. Mix 400 ml water with 200 ml liquid descaler to
make a descaling solution.
2. Use the ÿ On/Off button to start.
3. Remove the water tank and fill it with descaling
solution.
4. Once the water tank has been filled with descaling
solution, push it back in again fully.
5. Close the control panel.
6. Touch the Menu field.
The list of operating modes is displayed.
7. Touch the "Cleaning" text field.
8. Touch the "Descaling" text field.
The duration of the descaling programme is
displayed. It cannot be changed.
9. Press the Start/Stop button l to start.
The appliance is now descaled. The time counts down
in the display.
sounds.
1. Open the control panel.
2. Remove the water tank, rinse thoroughly, fill with
water and reinsert.
3. Close the control panel.
4. Press the l Start/Stop button to start.
The appliance rinses.
sounds.
1. Open the control panel.
2. Remove the water tank, rinse thoroughly, fill with
water and reinsert.
3. Close the control panel.
4. Press the l Start/Stop button to start.
The appliance rinses.
sounds.
1. Open the control panel.
2. Empty and dry the water tank.
3. Press the # On/Off button to switch off the
appliance.
use again.
time to come. This will tell you how to remove the
shelves and clean them.
The rails become very hot. Never touch the hot rails.
Always allow the appliance to cool down. Keep children
away from the appliance.
1. Lift the rail slightly at the front ‚ and detach it ƒ
2. Then pull the whole rail towards you and take it out
Clean the rails with cleaning agent and a sponge. For
stubborn deposits of dirt, use a brush.
The rails only fit on the right or the left side. The pull-out
rails must pull out towards you.
1. First, insert the rail in the middle of the rear socket ‚,
2. Then insert the rail into the front socket „, until the
