Handleiding Bosch GWX 18V-15 PSC (pagina 34 van 499) (Alle talen)

786203

Verklein

Vergroot

Pagina terug

1/499

Pagina verder

34 | English

Cutting stone

uFor cutting stone with bonded cutting discs or dia-

mond cutting discs for concrete/stone, always use the

extraction guard for cutting with a cutting guide(29)

or the protective guard for cutting(17) or the protect-

ive guard for grinding (15) with a fitted cover for

cutting(18).

uProvide sufficient dust extraction when cutting stone.

uWear a dust mask.

uThe power tool may be used only for dry cutting/grind-

ing.

uWhen using the protective guard for cutting(17) , the

protective guard for grinding(15) or the protective

guard for grinding(15) with a fitted cover for

cutting(18) for cutting and grinding applications in

concrete or masonry, there is an increased dust load

and an increased risk of losing control of the power

tool, which can lead to kickback.

For cutting stone, it is best to use a diamond cutting disc.

When using the extraction guard for cutting with a cutting

guide(29), the dust extractor must be approved for extract-

ing stone dust. Suitable dust extractors are available from

Bosch.

Switch on the power tool

and position it with the

front part of the cutting

guide on the workpiece.

Move the power tool with a

moderate feed motion that

is suited to the material be-

ing machined.

When cutting especially

hard materials such as con-

crete with a high pebble content, the diamond cutting disc

can overheat and become damaged as a result. This is

clearly indicated by circular sparking, rotating with the dia-

mond cutting disc.

If this happens, stop cutting and allow the diamond cutting

disc to cool down by running the power tool for a short time

at maximum speed with no load.

If work is noticeably slower and with circular sparking, this

indicates that the diamond cutting disc has become blunt.

You can resharpen the disc by briefly cutting into abrasive

material (e.g. lime-sand brick).

Cutting other materials

uFor cutting materials such as plastic, composite ma-

terials, etc. with bonded cutting discs or Carbide Multi

Wheel cutting discs, always use the protective guard

for cutting(17) or the protective guard for

grinding(15) with a fitted cover for cutting (18). You

can achieve improved dust extraction by using the ex-

traction guard with a cutting guide(29).

Working with Diamond Annular Cutters

uOnly use dry diamond annular cutters.

uAlways fit the hand guard (22) when working with dia-

mond annular cutters.

Do not place the diamond annular cutter parallel to the work-

piece. Plunge it into the workpiece at an angle and in a circu-

lar motion. This will allow you to achieve optimal cooling and

ensure a longer tool life for the diamond annular cutter.

Information on structural design

Recesses in load-bearing walls are subject to country-spe-

cific regulations. These regulations must be observed under

all circumstances. Seek advice from the responsible struc-

tural engineer, architect or construction supervisor before

starting work.

Start-up

Switching on/off

(GWX 18V-15 C / GWX 18V-15 SC)

To start the power tool, push the on/off switch (5) forward.

To lock the on/off switch (5) in position, push the on/off

switch (5) forward and down until it clicks into place.

To switch off the power tool, release the on/off switch (5);

or, if the switch is locked, briefly push the on/off switch (5)

backward and down and then release it.

uAlways check abrasive tools before using them. The

abrasive tool must be fitted properly and be able to

move freely. Carry out a test run for at least one

minute with no load. Do not use abrasive tools that are

damaged, run untrue or vibrate during use. Damaged

abrasive tools can burst apart and cause injuries.

Switching On/Off

(GWX 18V-15 P / GWX 18V-15 PSC)

To start the power tool, push the unlocking lever (10) for-

wards and then push the on/off switch (5) up.

To switch off the power tool, release the on/off switch (5).

uAlways check abrasive tools before using them. The

abrasive tool must be fitted properly and be able to

move freely. Carry out a test run for at least one

minute with no load. Do not use abrasive tools that are

damaged, run untrue or vibrate during use. Damaged

abrasive tools can burst apart and cause injuries.

1 609 92A 6WT | (24.06.2022) Bosch Power Tools

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Bosch GWX 18V-15 PSC Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info