Handleiding Bosch GWX 18V-10 SC (pagina 32 van 483) (Alle talen)

786186

Verklein

Vergroot

Pagina terug

1/483

Pagina verder

32 | English

Practical advice

Rough grinding

uAlways use the protective guard for grinding(14)

when rough grinding with bonded abrasives.

uNever use cutting discs for rough grinding.

uWhen rough grinding, the protective guard for

cutting(15) or the protective guard for grinding(14)

with a fitted cover for cutting(18) can impact the

workpiece and lead to a loss of control.

The best rough grinding results are achieved with a set angle

of 30° to 40°. Move the power tool back and forth with mod-

erate pressure. This will ensure that the workpiece does not

become too hot or discolour and that grooves are not

formed.

uThe protective guard for cutting(15) or the protective

guard for grinding(14) with a fitted cover for cutting(18)

must be used when using bonded discs which are ap-

proved for cutting and grinding.

Surface grinding with flap disc

uAlways use the protective guard for grinding(14)

when grinding with the flap disc.

The flap disc (accessory) enables you to machine curved

surfaces and profiles. Flap discs have a considerably longer

service life, lower noise levels and lower grinding temperat-

ures than conventional grinding discs.

Surface grinding with sanding disc

uAlways fit the hand guard (23) when working with the

rubber sanding pad (24).

Grinding with a sanding disc can be done without a protect-

ive guard.

See the graphics page for fitting instructions.

Cup brush/disc brush/conical brush

uAlways use the protective guard for grinding(14)

when brushing with disc brushes. Brushing with cup

brushes/conical brushes can be performed without

the protective guard.

uAlways fit the hand guard (23) when working with the

cup brush or conical brush.

uThe wires of the disc brush can get caught on the pro-

tective guard and break, if the maximum permitted di-

mensions of the disc brushes are exceeded.

See the graphics page for fitting instructions.

Cutting Metal

uFor cutting metal with bonded cutting discs or dia-

mond cutting discs, always use the protective guard

for cutting(15) or the protective guard for

grinding(14) with a fitted cover for cutting(18).

uWhen using the protective guard for grinding(14) for

cutting work with bonded cutting discs, there is an in-

creased risk of being exposed to sparks, particles and

disc fragments if the disc breaks.

When carrying out abrasive cutting, use a moderate feed

that is suited to the material being machined. Do not exert

pressure on the cutting disc and do not tilt or swing the

power tool.

Do not attempt to reduce the speed of a cutting disc coming

to a stop by applying pressure from the side.

The power tool must always

work in an up-grinding mo-

tion. Otherwise there is a

risk that it will be pushed

uncontrolled out of the cut.

For best results when cut-

ting profiles and rectangular

tubing, start at the smallest

cross section.

Cutting stone

uFor cutting stone with bonded cutting discs or dia-

mond cutting discs for concrete/stone, always use the

extraction guard for cutting with a cutting guide(30)

or the protective guard for cutting(15) or the protect-

ive guard for grinding (14) with a fitted cover for

cutting(18).

uProvide sufficient dust extraction when cutting stone.

uWear a dust mask.

uThe power tool may be used only for dry cutting/grind-

ing.

uWhen using the protective guard for cutting(15) , the

protective guard for grinding(14) or the protective

guard for grinding(14) with a fitted cover for

cutting(18) for cutting and grinding applications in

concrete or masonry, there is an increased dust load

and an increased risk of losing control of the power

tool, which can lead to kickback.

For cutting stone, it is best to use a diamond cutting disc.

When using the extraction guard for cutting with a cutting

guide(30), the dust extractor must be approved for extract-

ing stone dust. Suitable dust extractors are available from

Bosch.

Switch on the power tool

and position it with the

front part of the cutting

guide on the workpiece.

Move the power tool with a

moderate feed motion that

is suited to the material be-

ing machined.

When cutting especially

hard materials such as con-

crete with a high pebble content, the diamond cutting disc

can overheat and become damaged as a result. This is

clearly indicated by circular sparking, rotating with the dia-

mond cutting disc.

If this happens, stop cutting and allow the diamond cutting

disc to cool down by running the power tool for a short time

at maximum speed with no load.

If work is noticeably slower and with circular sparking, this

indicates that the diamond cutting disc has become blunt.

1 609 92A 766 | (17.02.2022) Bosch Power Tools

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Bosch GWX 18V-10 SC Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info