Handleiding Bosch GWX 18V-10 SC (pagina 29 van 483) (Alle talen)

786186

Verklein

Vergroot

Pagina terug

1/483

Pagina verder

English | 29

possible to check the state of charge when the power tool is

not in operation.

Press the button for the battery charge indicator or to

show the state of charge. This is also possible when the bat-

tery is removed.

If no LED lights up after pressing the button for the battery

charge indicator, then the battery is defective and must be

replaced.

The state of charge of the battery is also displayed on the

user interface (see "Status indications", page33).

Battery model GBA 18V...

LED Capacity

3× continuous green light 60–100%

2× continuous green light 30–60%

1× continuous green light 5–30%

1× flashing green light 0–5%

Battery model ProCORE18V...

LED Capacity

5 × continuous green light 80–100%

4 × continuous green light 60–80%

3 × continuous green light 40–60%

2 × continuous green light 20–40%

1 × continuous green light 5–20%

1 × flashing green light 0–5%

Recommendations for Optimal Handling of the

Battery

Protect the battery against moisture and water.

Only store the battery within a temperature range of −20 to

50°C. Do not leave the battery in your car in the summer, for

example.

Occasionally clean the ventilation slots on the battery using a

soft brush that is clean and dry.

A significantly reduced operating time after charging indic-

ates that the battery has deteriorated and must be replaced.

Follow the instructions on correct disposal.

Fitting

Using the Bluetooth® Low Energy Module

Note: The Bluetooth ® Low Energy ModuleGCY42 is avail-

able as an accessory for power toolsGWX18V-10PC; the

Bluetooth ® Low Energy ModuleGCY42 is included in the

scope of delivery of power toolsGWX18V-10SC / GWX

18V-10 PSC.

Read the corresponding operating instructions for informa-

tion about the Bluetooth® Low Energy ModuleGCY42.

Fitting Protective Equipment

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Note: If the grinding disc breaks during operation or the

holding fixtures on the protective guard/power tool become

damaged, the power tool must be sent to the after-sales ser-

vice immediately; see the "After-Sales Service and Applica-

tion Service" section for addresses.

Protective guard for grinding

Place the protective guard

(14) onto the holder on the

power tool until the coding

cams of the protective guard

are aligned with the holder.

When doing so, press and

hold the unlocking lever (1).

Press the protective guard

(14) onto the spindle collar

until the shoulder of the pro-

tective guard is sitting on the

flange of the power tool and

rotate the protective guard

until it audibly clicks into

place.

Adjust the position of the protective guard (14) to meet the

requirements of the operation. To do this, push the unlock-

ing lever (1) upward and rotate the protective guard (14)

into the required position.

uAlways position the protective guard(14) such that

the two cams on the unlocking lever(1) engage in the

corresponding openings on the protective guard(14).

uAdjust the protective guard (14) such that sparking in

the direction of the operator is prevented.

uThe protective guard (14) must only be adjustable

while the unlocking lever (1) is actuated. Otherwise,

the power tool must not be used any more under any

circumstances and must be sent to the after-sales ser-

vice.

Note: The coding cams on the protective guard (14) ensure

that only a protective guard that is suitable for the power

tool can be fitted.

Protective guard for cutting

uFor cutting, always use the protective guard for

cutting(15) or the protective guard for grinding (14)

together with the cover for cutting(18).

uProvide sufficient dust extraction when cutting stone.

The protective guard for cutting(15) is fitted in the same

way as the protective guard for grinding(14).

Bosch Power Tools 1 609 92A 766 | (17.02.2022)

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Bosch GWX 18V-10 SC Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info