79060
18
Verklein
Vergroot
Pagina terug
1/261
Pagina verder
English - 5
An O-ring (plastic
part) is inserted in
the mounting
flange 9 around the
spigot.
If the O-ring is missing or is damaged, it must
in all cases be replaced (Order No.
1 600 210 039) before the mounting flange 9 is
mounted.
After mounting the grinding tool and be-
fore switching on, check that the grind-
ing tool is correctly mounted and that it
can turn freely.
Flap Disc
Depending on the application, remove the protec-
tion guard 6 and mount the hand guard 18. Place
the special mounting flange 9 (accessory, Order
No. 2 605 703 028) and the flap disc on the
grinder spindle 5. Screw on the clamping nut 11
and tighten with the two-pin spanner.
Rubber Sanding Plate 20
Depending on the application, remove the protec-
tion guard 6 and mount the hand guard 18.
Before mounting the rubber sanding pad 20,
place the 2 spacers 19 onto the grinding spindle.
For mounting, see the illustration page.
Screw on the round nut 22 and tighten with the
two-pin spanner.
Cup Brush 23/Disc Brush
Depending on the application, remove the protec-
tion guard 6 and mount the hand guard 18.
The grinding tool must be able to be screwed
onto the grinding spindle 5 until it rests firmly
against the grinder spindle flange at the end of
the grinder spindle threads. Tighten with an
open-end spanner.
Grinding Cup
When working with grinding cups, use
the special guard 15.
The grinding cup 16 should always protrude
from the guard 15 only as far as absolutely nec-
essary for the work to be performed in each case.
Adjust the guard 15 to this distance.
For mounting, see the illustration page.
Screw on the clamping nut 11 and tighten with
the fitting offset two-pin spanner 17.
Instead of the clamping nut 11, the quick-clamp-
ing nut 12 (accessory) can be used. Grinding
tools can then be mounted without using tools.
The quick-clamping nut 12 may be used only
for grinding and cutting discs.
Use only a flawless, undamaged quick-clamp-
ing nut 12.
When screwing on, take care that the side with
printing does not point to the grinding disc. The
arrow must point to the index mark 29.
Lock the grinder
spindle with the spin-
dle lock button 2.
Tighten the quick-
clamping nut by
forcefully turning the
grinding disc in the
clockwise direction.
A properly tightened
undamaged, quick-
clamping nut can be
loosened by hand
turning the knurled
ring in anticlockwise
direction.
Never loosen a tight
quick-clamping nut
with pliers but use a
two-pin spanner. In-
sert the two-pin
spanner as shown in
the illustration.
9
Quick Clamping Nut
2
29
12
2
1 609 929 R35.book Seite 5 Mittwoch, 13. Februar 2008 1:16 13
19 • 1 609 929 R35 • 03.11
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch GWS 21-230 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch GWS 21-230 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 12,05 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info