Handleiding Bosch GWS 11-125 P (pagina 26 van 395) (Alle talen)

786323

Verklein

Vergroot

Pagina terug

1/395

Pagina verder

26 | English

Hand guard

uAlways fit the hand guard (21) when working with the

rubber sanding pad (22) or with the cup brush/conical

brush/diamond annular cutter.

Attach the hand guard(21) to the auxiliary handle(6)/(32).

Standard auxiliary handle/low-vibration auxiliary handle

Screw the auxiliary handle (6)/(32) on the right or left of the

machine head depending on the working method.

uDo not operate your power tool without the auxiliary

handle(6)/(32).

uDo not continue to use the power tool if the auxiliary

handle (6)/(32) is damaged. Do not make any altera-

tions to the auxiliary handle (6)/(32).

The low-vibration auxiliary

handle (32) reduces vibra-

tion, enabling the tool to be

used safely and more com-

fortably.

Fitting the Abrasive Tools

uPull the plug out of the socket before carrying out any

work on the power tool.

uDo not touch grinding and cutting discs until they have

cooled down. The discs can become very hot while work-

ing.

Clean the grinding spindle (18) and all the parts to be fitted.

Lock the grinding spindle with the spindle lock button (2)

before clamping and releasing the abrasive tools.

uDo not press the spindle lock button while the grind-

ing spindle is moving. The power tool may become dam-

aged if you do this.

Grinding/cutting disc

Pay attention to the dimensions of the abrasive tools. The

diameter of the hole must match that of the mounting flange.

Do not use an adapter or reducer.

When using diamond cutting discs, make sure that the direc-

tion of rotation arrow on the diamond cutting disc corres-

ponds to the direction of rotation of the machine (see direc-

tion of rotation arrow on the housing).

See the graphics page for fitting instructions.

Note: When assembling bonded grinding or cutting discs us-

ing the supplied mounting flange(10) and the clamping

nut(15) or quick-clamping nut(16), the use of intermediate

layers is not necessary.

To secure the grinding/cutting disc, place the mounting

flange with O-ring(10) on the grinding spindle(18) and

screw on the clamping nut(15). Pay attention to the align-

ment of the clamping nut(15) depending on the grinding/

cutting disc that is being used (see figures at the beginning

of the.operating manual), and tighten it with the two-pin

spanner (see " Quick-clamping nut ",

page26).

uAfter fitting the abrasive tool, check that the abrasive

tool is fitted correctly and can turn freely before

switching on the power tool. Make sure that the abras-

ive tool does not brush against the protective guard or

other parts.

A plastic part (O-ring) is fitted around the cent-

ring collar in the mounting flange (10). If the

O-ring is missing or damaged, the mounting

flange (10) must be replaced before operation

can resume.

Quick-clamping nut

To change the abrasive tool easily without having to use any

additional tools, you can use the quick-clamping nut (16) in-

stead of the clamping nut (15).

uThe quick-clamping nut (16) may be used only for

grinding or cutting discs.

Only use quick-clamping nuts (16) that are in good work-

ing order and not damaged.

When screwing on, make sure that the printed side of the

quick-clamping nut (16) is not facing the grinding disc;

the arrow must be pointing towards the index mark (33).

(33)

Press the spindle lock but-

ton (2) to lock the grinding

spindle. To tighten the

quick-clamping nut, turn

the grinding disc firmly

clockwise.

If the quick-clamping nut

has been attached correctly

and is not damaged, you

can loosen it by hand by

turning the knurled ring an-

ticlockwise. If the quick-

clamping nut is stuck, do

not attempt to loosen it

with pliers – always use

the two-pin spanner. Posi-

tion the two‑pin spanner as

shown in the figure.

Approved abrasive tools

You can use all the abrasive tools mentioned in these operat-

ing instructions.

The permissible speed [min-1] or the circumferential speed

[m/s] of the abrasive tools used must at least match the val-

ues given in the table.

It is therefore important to observe the permissible rota-

tional/circumferential speed on the label of the abrasive

tool.

1 609 92A 7AL | (30.03.2022) Bosch Power Tools

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Bosch GWS 11-125 P Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info