544116
17
Verklein
Vergroot
Pagina terug
1/217
Pagina verder
English | 17
Bosch Power Tools 1 619 P11 351 | (1.10.13)
The optimal orbital action setting for the respective applica-
tion can be determined through practical testing. The follow-
ing recommendations apply:
Select a lower orbital action setting (or switch it off) for a
finer and cleaner cutting edge.
For thin materials such as sheet metal, switch the orbital
action off.
For hard materials such as steel, work with low orbital
action.
For soft materials and when sawing in the direction of the
grain, work with maximum orbital action.
Adjusting the Cutting Angle (see figure J)
The base plate 9 can be swivelled by 45° to the left or right for
mitre cuts.
Remove the vacuum connection 20.
In mitre angle 0° there is a pin in a corresponding recess.
Loosen the screw 24 with the Allen key 29 until you can slide
the base plate 9 in toward the battery 1. Let the pin slide into
the guide groove.
For adjustment of precise mitre angles, swivel the base plate
9 to the desired position according to the scale 25. Every an-
gle can be adjusted to 45° using a protractor.
Tighten the screw 24 again.
The vacuum connection 20 and the splinter guard 22 cannot
be used for bevel cuts.
Starting Operation
Removing the battery (see figure K)
To remove the battery 1 press the unlocking buttons 2 and
pull out the battery downwards. Do not exert any force.
Switching On and Off
To start the machine, push the On/Off switch 7 forwards.
To switch off the power tool, push the On/Off switch 7 back
to the “0” position.
To save energy, only switch the power tool on when using it.
Controlling the Stroke Rate
With the thumbwheel for stroke rate preselection 4, the
stroke rate can be preset and changed during operation.
The required stroke rate is dependent on the material and the
working conditions and can be determined by a practical trial.
Reducing the stroke rate is recommended when the saw
blade engages in the material as well as when sawing plastic
and aluminium.
After longer periods of work at low stroke rate, the machine
can heat up considerably. Remove the saw blade from the ma-
chine and allow the machine to cool down by running it for ap-
prox. 3 minutes at maximum stroke rate.
Temperature Dependent Overload Protection
In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or not kept within the
permitted battery temperature range, the speed is reduced or
the power tool switches off. At reduced speed, the power tool
will run again at full speed once the permitted battery temper-
ature is reached or the load is reduced. During automatic
shut-down, switch off the power tool, allow the battery to cool
down, then switch the power tool back on.
Temperature Control/Overload Protection Indicator
The red LED indicator 6 will help you in protecting the battery
against overheating and the motor against overloading.
When the LED indicator 6 continuously lights up red, the
temperature of the battery is too high and the machine
switches off automatically.
Switch the power tool off.
Allow the battery to cool down before continuing to work.
The LED indicator 6 flashes red, the power tool is blocked
and switches off automatically.
Remove the power tool from the workpiece.
As soon as the blockage is corrected, the power tool will con-
tinue to work at the set stroke rate.
Protection Against Deep Discharging
The lithium ion battery is protected against deep discharging
by the “Electronic Cell Protection (ECP)”. When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
Switching on the LED Work Area Illumination
With the button 3 you can switch on the LED work light. The
work light is switched off by default.
Restarting Protection
The restarting protection prevents uncontrolled starting of
the machine after a power failure. Once the restarting protec-
tion is active, the temperature control/overload protection in-
dicator blinks 6 continuously.
To restart the operation, switch the On/Off switch 7 to the
Off position and start the machine again.
Note: When switching off and on again very quickly, it is pos-
sible that the restarting protection is triggered; this will pre-
vent the power tool from starting, although the On/Off switch
7 is actuated. Set the On/Off switch 7 to the off position, and
then switch the power tool on again.
Working Advice
When sawing small or thin workpieces, always use a
firm support.
Contact Protector
The contact protector 19 attached to the casing prevents
accidental touching of the saw blade during the working pro-
cedure and may not be removed.
The outwardly curved edge over the extraction hood 16 pre-
vents the hand from slipping away in the sawing range.
Plunge Cutting (see figure G)
Plunge cuts may only be applied to soft materials, such
as wood, gypsum plaster boards, etc.!
Use only short saw blades for plunge cutting. Plunge cutting is
possible only with the mitre angle set at 0°.
Place the machine with the front edge of the base plate 9 on
to the workpiece without the saw blade 14 touching the work-
piece and switch on. For machines with stroke rate control,
OBJ_BUCH-1994-001.book Page 17 Tuesday, October 1, 2013 2:18 PM
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch GST 10.8 V-LI bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch GST 10.8 V-LI in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 9,68 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info