Handleiding Bosch GSS 18V-10 (pagina 15 van 205) (Alle talen)

786281

Verklein

Vergroot

Pagina terug

1/205

Pagina verder

English | 15

increase the vibration and noise emissions over the total

working period.

To estimate vibration and noise emissions accurately, the

times when the tool is switched off or when it is running but

not actually being used should also be taken into account.

This may significantly reduce vibration and noise emissions

over the total working period.

Implement additional safety measures to protect the oper-

ator from the effects of vibration, such as servicing the

power tool and application tools, keeping their hands warm,

and organising workflows correctly.

Assembly

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Charge the battery

uUse only the chargers listed in the technical data. Only

these chargers are matched to the lithium-ion battery of

your power tool.

Note: The battery is supplied partially charged. To ensure

full battery capacity, fully charge the battery in the charger

before using your power tool for the first time.

The lithium-ion battery can be charged at any time without

reducing its service life. Interrupting the charging process

does not damage the battery.

The lithium-ion battery is protected against deep discharge

by the "Electronic Cell Protection (ECP)". When the battery

is discharged, the power tool is switched off by means of a

protective circuit: The application tool no longer rotates.

uDo not continue to press the On/Off switch after the

power tool has automatically switched off. The battery

can be damaged.

To remove the battery (11), press the release button (12)

and pull the battery sideways out of the power tool. Do not

use force to do this.

Follow the instructions on correct disposal.

Fitting the base plate (see figure A)

Unscrew the four screws (14) completely. Fit a suitable base

plate and retighten the screws.

Changing the sanding plate (see figure A)

If necessary, the sanding plate (3) can be replaced.

Unscrew the four screws (14) completely and remove the

sanding plate (3). Fit the new sanding plate (3) and

retighten the screws.

Changing the sanding sheet

Remove dirt and dust from the sanding plate (3), e.g. with a

brush, before attaching a new sanding sheet.

To ensure optimum dust extraction, make sure that the

punched holes in the sanding sheet are aligned with the

drilled holes in the sanding plate.

Sanding sheets without hook-and-loop backing (see

figures B–D)

Unlock both sanding-sheet clamps (4) and swivel them

downwards.

Insert the sanding sheet (6) under the rear clamping

bracket (2). Ensure that the sanding sheet (6) is not too

short and that it is correctly clamped. Swivel the sand-

ing-sheet clamp (4) back into the starting position and

lock it in place.

Position the sanding paper so that it fits tightly around

the sanding plate (3). Clamp the front part of the sand-

ing sheet under the front clamping bracket (7). Ensure

that the sanding sheet (6) is not too short and that it is

correctly clamped. Swivel the sanding-sheet clamp (4)

back into the starting position and lock it in place.

Unperforated sanding sheets, e.g. from rolls or bulk stock

sold by the metre, can be perforated using the punch (19)

for the purpose of dust extraction. To do this, fit the sanding

sheet on the power tool and push the tool down onto the

punch (see figureG).

To remove the sanding sheet (6), unlock both sanding-sheet

clamps (4) and pull the sanding sheet out of its bracket.

Selecting a sanding sheet

Different sanding sheets are available, depending on the ma-

terial you are working with and the required surface removal

rate:

Grit

For processing all wood and wood-based ma-

terials

40–180

For pre-sanding, e.g. of rough and un-

even beams and boards Coarse 40

For surface sanding and levelling of

slight irregularities Medium 80, 120

For finish-sanding and fine sanding of

hardwoods Fine 180

For processing paint and lacquer layers or

primers such as fillers and bodyfillers

40–180

For sanding down paint Coarse 40

For sanding undercoats Medium 80, 120

For final sanding of primers prior to

painting Fine 180

For any finishing work, such as polishing (metal and stone in

particular), use fleece/polishing felt.

Different types of fleece and polishing felts should be used

depending on the surface finish required on the workpiece.

Bosch Power Tools 1 609 92A 7TF | (24.06.2022)

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Bosch GSS 18V-10 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info