78650
36
Verklein
Vergroot
Pagina terug
1/46
Pagina verder
35
English
21. The saw blades body must be thinner than the
riving knife and the width of cut, or kerf (with
teeth set) must be greater than the thickness of
the riving knife.
22. Never operate the circular saw with the saw blade
turned upward or the side.
23. Ensure that the material is free of foreign matters
such as nails.
24. The riving knife should always be used except
when plunging in the middle of the workpiece.
25. The saw blades range should be from 165 mm
to 150 mm.
26. Be careful of brake kickback.
This circular saw features an electric brake that
functions when the switch is released. As there
is some kickback when the brake functions, be
sure to hold the main body securely.
27. Avoid cutting in the state where the base has
floated up from the material.
When blade is binding, or when interrupting a cut
for any reason, release the trigger and hold the
saw motionless in the material until the blade
comes to a complete stop. Never attempt to
remove the saw from the work or pull the saw
backward while the blade is in motion or KICKBACK
may occur. Investigate and take corrective actions
to eliminate the cause of blade binding.
28. Support large panels to minimize the risk of blade
pinching and KICKBACK. Large panels tend to sag
under their own weight. Supports must be placed
under the panel on both sides, near the line of
cut and near the edge of the panel as shown in
Fig. 1.
To minimize the risk of blade pinching and kickback.
When cutting operation requires the resting of the
saw on the work piece, the saw shall be rested
on the larger portion and the smaller piece cut
off.
29. Use extra caution when making a Pocket Cut
into existing walls or other blind areas. The
protruding blade may cut objects that can cause
KICKBACK.
NEVER place your hand or fingers behind the saw
(Fig. 3). If kickback occurs, the saw could easily
jump backwards over your hand, possibly causing
severe injury.
30. WARNING: It is important to support the work
piece properly and to hold the saw firmly to
prevent loss of control which could cause personal
injury. Fig. 4 illustrates typical hand support of the
saw.
31. Place the wider portion of the saw base on that
part of the work piece which is solidly supported,
not on the section that will fall off when the cut
is made. As examples, Fig. 5 illustrates the RIGHT
way to cut off the end of board, and Fig. 6 the
WRONG way. If the work piece is short or small,
clamp is down.
DONT TRY TO HOLD SHORT PLACES BY HAND!
32. Never attempt to saw with the circular saw held
upside down in a vise. This is extremely dangerous
and can lead to serious accidents. (Fig. 7)
33. When the brake becomes ineffective, replace the
carbon brushes with new ones.
SPECIFICATIONS
POWER TOOL
CHARGER
Model UC24YFA
Charging voltage 7.2 24V
Weight 0.6 kg
Model C6DD
No-load speed 2600 min
1
Capacity Cutting depth
90° 55 mm
45° 40 mm
Rechargeable battery Ni-Cd battery, 18V
Light bulb 12V, 5W
Weight 4.4 kg
36

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch GSR 12,0-2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch GSR 12,0-2 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,72 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info