544376
12
Verklein
Vergroot
Pagina terug
1/130
Pagina verder
1 609 92A 01G | (9.1.13) Bosch Power Tools
12 | English
Do not point the tool towards yourself or anyone
nearby. Unexpected triggering will discharge the fas-
tener causing an injury.
Do not actuate the tool unless the tool is placed firm-
ly against the workpiece. If the tool is not in contact
with the workpiece, the fastener may be deflected away
from your target.
Disconnect the tool from the power source when the
fastener jams in the tool. While removing a jammed
fastener, the tacker may be accidentally activated if it is
plugged in.
Use caution while removing a jammed fastener. The
mechanism may be under compression and the fasten-
er may be forcefully discharged while attempting to free
a jammed condition.
Do not use this tacker for fastening electrical cables.
It is not designed for electric cable installation and may
damage the insulation of electric cables thereby causing
electric shock or fire hazards.
Use appropriate detectors to determine if utility
lines are hidden in the work area or call the local util-
ity company for assistance. Contact with electric lines
can lead to fire and electric shock. Damaging a gas line
can lead to explosion. Penetrating a water line causes
property damage.
Observe the conditions of the job site. It is possible
that fasteners can burst through thin workpieces or be
deflected when working in corners or against edges,
and harm persons.
When working, hold the power tool in such a manner
that your head and body cannot be injured in case of
sudden kickback due to a malfunction of the energy
supply or from hard objects/locations in the work-
piece.
Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e. g.,
against continuous intense sunlight, fire,
water, and moisture. Danger of explosion.
In case of damage and improper use of the battery,
vapours may be emitted. Ventilate the area and seek
medical help in case of complaints. The vapours can
irritate the respiratory system.
Use the battery only in conjunction with your Bosch
power tool. This measure alone protects the battery
against dangerous overload.
Use only original Bosch batteries with the voltage
listed on the nameplate of your power tool. When us-
ing other batteries, e.g. imitations, reconditioned bat-
teries or other brands, there is danger of injury as well
as property damage through exploding batteries.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Intended Use
The power tool is intended for connecting work in roofing,
encasing, battening, manufacturing wall and ceiling ele-
ments, wood facades, pallets, wood fences, noise-reduc-
tion walls and boxes.
Only the fasteners (nails, staples, etc.) specified in table
“Technical Data” may be used.
Product Features
The numbering of the product features refers to the illus-
tration of the machine on the graphics page.
1 Workpiece protector
2 Discharge lock-off
3 Clamping lever for opening/closing the shot duct
4 Thumbwheel for depth stop adjustment
5 Switch for blocking the actuation system
6 Trigger
7 Battery unlocking button
8 Battery pack
9 Handle (insulated gripping surface)
10 Storage for workpiece protector
11 Belt hook
12 Magazine
13 Magazine slider
14 Nail pusher
15 Outlet
16 Nail strip*
17 Magazine spring
*Accessories shown or described are not part of the standard
delivery scope of the product. A complete overview of accesso-
ries can be found in our accessories program.
Technical Data
Noise/Vibration Information
Measured sound values determined according to
EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 91 dB(A); Sound power level
102 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
h
and uncertainty K determined ac-
cording to EN 60745:a
h
<2.5m/s
2
, K=1.5 m/s
2
.
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool
with another. It may be used for a preliminary assessment
of exposure.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for dif-
ferent applications, with different accessories or poorly
maintained, the vibration emission may differ. This may
significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should
also take into account the times when the tool is switched
off or when it is running but not actually doing the job. This
may significantly reduce the exposure level over the total
working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and
the accessories, keep hands warm, organise work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product
described under “Technical Data” is in conformity with the
following standards or standardization documents:
EN 60745 according to the provisions of the directives
2011/65/EU, 2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 09.01.2013
Assembly
Battery Charging
Use only the battery chargers listed on the graphics
page. Only these battery chargers are matched to the
lithium ion battery used in your machine.
Note: The battery is supplied partially charged. To ensure
full capacity of the battery, completely charge the battery
in the battery charger before using your power tool for the
first time.
The Lithium-Ion battery can be charged at any time without
reducing its service life. Interrupting the charging proce-
dure does not damage the battery.
The “Electronic Cell Protection (ECP)” protects the lithium
ion battery against deep discharging. When the battery is
discharged, the power tool is switched off by a protective
circuit: Fasteners can no longer be shot.
After the automatic shut-off of the
power tool, do not continue to press
the trigger. The battery could become damaged.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of
between 0 °C and 45 °C. A long battery service life is
achieved in this manner.
Observe the notes for disposal.
Removing the battery (see figure A)
The battery 8 has two locking levels, which are supposed
to prevent the battery from falling out in case of vibrations
from intensive use.
Press battery unlocking button 7 (1.) and at the same
time push the battery toward the front.
Press the battery unlocking button 7 (2.) again and pull
the battery out completely, toward the rear.
Loading the Magazine (see figures B1 B4)
Block the actuation system and remove
the battery before making any adjust-
ments, changing accessories, or placing
the power tool aside. This safety measure
prevents accidental starting of the power
tool.
Use only original Bosch accessories (see “Technical
Data”). The precision parts of the power tool, such as
the magazine, the outlet and the shot duct, are matched
to Bosch staples, nails and brads. Other manufacturers
use other steel qualities and sizes.
Using fasteners not permitted can damage the power
tool and cause injuries.
While loading the magazine, hold the power tool in such a
manner that the outlet 15 is not pointed at your own body
or at other persons.
Clean the magazine slider 13 as required and make sure
that the magazine 12 is not dirty/soiled.
Insert a fitting nail strip 16 in the T-slot at the end of the
magazine 12.
Push the nail strip in the magazine toward the front until
the last nail is positioned in front of the magazine spring
17.
Note: A lock function of the magazine slider prevents the
power tool from being started with an empty magazine.
The discharge lock-off cannot be pressed in and blank fir-
ing is thus prevented.
Press the pretensioned nail pusher 14 against the mag-
azine slider 13 and at the same time, pull the magazine
slider completely to the end of the magazine 12.
Note: The magazine slider must slide back with only low
force (finger-pressure). A tight-running magazine slider
causes the nails to be driven in at an incorrect angle.
Cordless nailer GSK 18 V-LI
Article number
3 601 D80 3..
Actuation system
Single actuation with safe-
ty run
Fastener
–Type
–Length
–Diameter
–Angle
mm
mm
Brads
32 –64
1.6
20°
Magazine capacity, max.
105
Dimensions
Height
–Width
–Length
mm
mm
mm
295
96
334
Weight according to
EPTA-Procedure 01/2003
kg 3.3/3.5*
Battery
Li-Ion
Rated voltage
V= 18
Capacity
Ah 3.0
Operating duration with 3.0
Ah battery pack (continuous
operation)
approx. 700 nails
*dependent of the battery pack being used
Dr. Egbert Schneider
Senior Vice President
Engineering
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
OBJ_BUCH-1335-004.book Page 12 Wednesday, January 9, 2013 1:22 PM
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch GSK 18 V-LI bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch GSK 18 V-LI in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 16,04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info