Handleiding Bosch GOF 1250 CE Professional (pagina 18 van 230) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins)

593168

Verklein

Vergroot

Pagina terug

1/230

Pagina verder

18 | English

1 609 92A 16H | (16.2.15) Bosch Power Tools

Switching On and Off

Adjust the depth-of-cut before switching on or off; see Sec-

tion “Adjusting the Depth-of-cut”.

To start the machine, press the On/Off switch 29 and keep it

pressed.

To lock the pressed On/Off switch 29, press the lock-on but-

ton 2.

To switch off the machine, release the On/Off switch 29 or

when it is locked with the lock-on button 2, briefly press the

On/Off switch 29 and then release it.

To save energy, only switch the power tool on when using it.

Constant Electronic Control

Constant electronic control holds the speed constant at no-

load and under load, and ensures uniform working perfor-

mance.

Soft Starting

The electronic soft starting feature limits the torque upon

switching on and increases the working life of the motor.

Overload Protection

The overload protection prevents impermissibly high current

consumption in the event of extreme overload. This can lead

to a reduction in motor speed and power output or in extreme

cases to motor standstill.

Once the load has been removed from the power tool, the mo-

tor immediately runs up or back to working speed.

Restarting Protection

The restarting protection feature prevents uncontrolled restart-

ing of the machine after an interruption in the power supply.

To restart the operation, switch the On/Off switch 29 to the

Off position and start the machine again.

Release lever (see figure C)

The release lever 23 is automatically reset when you let go of

it. For better holding force, the release lever 23 must be

pulled back all the way. The holding force can be readjusted if

required. To do so, insert an Allen key (4 mm) into the open-

ing on the handle. Turn the Allen key clockwise to increase the

holding force, and turn it anticlockwise to reduce the holding

force.

Adjusting the Depth-of-cut (see figure D and E)

 The adjustment of the depth-of-cut may only be carried

out when the router is switched off.

For coarse adjustment of the depth-of-cut, proceed as fol-

lows:

– Place the machine with the router bit mounted on the

workpiece to be machined.

– Set the fine-adjustment path to the centre position with

the adjustment knob 25. For this, turn the adjustment

knob 25 until the marks 19 match as shown in the figure.

Afterwards, set the scale 24 to “0”.

– Set the step buffer 9 to the lowest position; the step buffer

engages noticeably.

– Loosen the screw 15 on the depth stop 14 so that the

depth stop 14 is freely movable.

– Press the release lever 23 back and slowly guide the router

down until the router bit 5 touches the workpiece surface.

Let go of the release lever 23 again to lock this position.

– Press the depth stop 14 down until it sits on the step buffer

GOF 1250 LCE: Switch on the digital depth setting at the

On/Off switch 18. Press the button 16 for setting the zero

point of the depth stop 14.

GOF 1250 CE: Set the slide with the index mark 27 to po-

sition “0” on the depth-of-cut scale 26.

– Set the depth stop 14 to the required depth-of-cut and

tighten the screw 15 on the depth stop 14.

GOF 1250 CE: Make sure you do not adjust the slide with

the index mark 27 any more.

– Push the release lever 23 and guide the plunge router to

the uppermost position.

For deep cuts, it is recommended to carry out several cuts,

each with little material removal. By using the step buffer 9,

the cutting process can be divided into several steps. For this,

adjust the desired depth-of-cut with the lowest step of the

step buffer and select the higher steps first for the initial cuts.

The clearance of the steps can be changed by screwing the

adjusting screws 10 further in or out.

After a test run, the depth-of-cut can be set to the required di-

mension by turning the adjustment knob 25; turning in a

clockwise direction increases the depth-of-cut; turning in an

anticlockwise direction decreases the depth-of-cut. The scale

24 can be used for guidance. One revolution corresponds

with a setting range of 2,0 mm, one of the graduation marks

on the bottom edge of the scale 24 changes the setting range

by 0,1 mm. The maximum setting range is ± 8 mm.

Example: The required depth-of-cut should be 10.0 mm, and

the test cut resulted in a depth-of-cut of 9.6 mm.

–Turn the scale 24 to “0”.

– Turn the adjustment knob 25 clockwise by 0.4 mm/4 grad-

uation marks (difference between target and actual val-

ues).

– Check the selected depth-of-cut by carrying out another

trial cut.

GOF 1250 CE: After setting the depth-of-cut, do not change

the position of the slide 27 on the depth stop 14 any more so

that you can always read the current depth-of-cut on the scale

26.

GOF 1250 LCE: The current depth-of-cut is shown on the dis-

play 21.

Working Advice

 Protect router bits against shock and impact.

Direction of Feed and Routing Process (see figure F)

 The routing process must always be carried out against

the rotation direction of the router bit 5 (up-cutting

motion). When routing in the direction with the rota-

tion of the router (down-cutting), the machine can

break loose, eliminating control by the user.

OBJ_BUCH-2018-004.book Page 18 Monday, February 16, 2015 1:39 PM

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Bosch GOF 1250 CE Professional Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info