592529
13
Verklein
Vergroot
Pagina terug
1/159
Pagina verder
English | 13
Bosch Power Tools 1 609 929 M22 | (8.10.07)
Operation
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V
can also be operated with 220 V.
Switching On and Off
To start the machine, push the On/Off switch 1
forward so that the “I” is indicated on the
switch.
To switch off the machine, push the On/Off
switch 1 toward the rear so that the “0” is indi-
cated on the switch.
Locking/Loosening the Die
For straight cuts, tighten the locking screw 3
using an Allen key (size 2.5 mm) in order to lock
the die 4.
For curved cuts, loosen the locking screw 3. The
die 4 can move freely now and adjusts to the di-
rection of the feed strength.
Working Advice
Apply the machine to the workpiece only when
switched on. Always hold the machine vertical to
the surface of the steel sheet and do not tilt it.
The cut takes place during the upward motion of
the punch. Guide the machine evenly and with
moderate feed in the cutting direction. A too high
feed rate significantly reduces the service life of
the cutting tools and can damage the machine.
If the punch should become wedged during cut-
ting, switch the machine off, relubricate the
punch and release the tension of the steel
sheet. Do not exert force, otherwise the punch
and die will become damaged.
f Wear protective gloves while working and
pay particular attention to the mains cable.
Sharp burrs develop at the cut steel sheet
and can cause injuries to the operator or
damage the mains cable.
f Exercise caution when handling the cutting
chips. The chips have sharp tips that can
cause injuries.
Maximum Steel Sheet Cutting Capacity
The maximum steel sheet cutting capacity d
max
depends on the strength properties of the ma-
terial to be cut.
The machine allows for straight and deformation-
free cutting of metal sheets to the following
thicknesses:
Lubricating/Cooling the Punch
To extend the service life of the punch 5, a lubri-
cating agent with good cooling properties (e.g.
cutting oil) should be used.
Apply a trail of lubricant beads onto the top side
of the metal sheet alongside the intended cut-
ting line. For long periods of continual use or for
work with high frictional wear (e.g. when cut-
ting aluminium), the cutting head should be
immersed into a container with lubricant in
regular intervals.
Cutting along a Cutting Mark or with a Guide
Straight cuts are carried out easier when the
machine is guided alongside a rule.
Contours can be cut by guiding the machine
along a template.
For inside cuts, pre-drilling a hole with a dia-
meter of 16 mm is necessary.
Material Max. strength
property
[N/mm
2
]
d
max
[mm]
Steel 400 2.0
600 1.4
800 1.0
Aluminium 200 2.5
OBJ_BUCH-236-002.book Page 13 Monday, October 8, 2007 11:54 AM
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch GNA 2.0 Professional bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch GNA 2.0 Professional in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 7,34 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info