592528
10
Verklein
Vergroot
Pagina terug
1/112
Pagina verder
10 | English
1 619 929 J61 | (25.7.11) Bosch Power Tools
Changing the Cutting Direction
For changing the cutting direction, the die holder 4 can be
turned to three positions, each offset by 90°. Cutting toward
the rear (toward the housing of the machine) is not possible.
For turning the die holder 4 loosen the screw 2 until you can
turn the die holder. Turn it 90 ° to the right or the left in rela-
tion to the longitudinal axle of the power tool.
Make sure that the screw 2 engages into the borehole of the
die holder 4. Tighten the screw 2.
Working Advice
f Before any work on the machine itself, pull the mains
plug.
f The power tool is not suitable for stationary operation.
For example, it may not be clamped in a vice or fastened on
a workbench.
f Wear protective gloves while working and pay particu-
lar attention to the mains cable. Sharp burrs develop at
the cut steel sheet and can cause injuries to the operator or
damage the mains cable.
f Exercise caution when handling the cutting chips. The
chips have sharp tips that can cause injuries.
Apply the machine to the workpiece only when switched on.
Always hold the machine vertical to the surface of the steel
sheet and do not tilt it.
The cut takes place during the downward motion of the
punch. Guide the machine evenly and with moderate feed in
the cutting direction. A high feed rate significantly reduces
the service life of the cutting tools and can damage the ma-
chine.
The machine operates more quietly when it is raised slightly
during cutting. If the punch should become wedged during
cutting, switch the machine off, relubricate the punch and re-
lease the tension of the steel sheet. Do not exert force, other-
wise the punch and the die will become damaged.
Maximum Steel Sheet Cutting Capacity
The maximum steel sheet cutting capacity d
max
depends on
the strength properties of the material to be cut.
The machine allows for straight and deformation-free cutting
of metal sheets to the following thicknesses:
Lubricating/Cooling the Punch
To extend the service life of the punch 3, a lubricating agent
with good cooling properties (e.g. cutting oil) should be used.
Apply a trail of lubricant beads onto the top side of the metal
sheet alongside the intended cutting line. For long periods of
continual use or for work with high frictional wear (e.g. when
cutting aluminium), the cutting head should be immersed into
a container with lubricant in regular intervals.
Cutting along a Cutting Mark or with a Guide
Straight cuts are carried out easier when the machine is guid-
ed alongside a rule.
Contours can be cut by guiding the machine along a template.
For inside cuts, pre-drilling a hole with a diameter of 21 mm is
necessary.
Maintenance and Service
Maintenance and Cleaning
f Before any work on the machine itself, pull the mains
plug.
f For safe and proper working, always keep the machine
and ventilation slots clean.
Clean and lubricate the punch 3 and die 5 every 3 operating
hours.
Change the punch and die in good time when worn. Only
sharp tools produce a good cutting quality and make the ma-
chine last longer.
The punch 3 and the die 5 may not be reground.
Changing the Die
Unscrew the knurled screw 7 of the die holder 4. Take out the
die 5.
Il necessary, clean the die holder 4.
Put a new, well greased die 5 into the die holder. Pay attention
to the alignment of the flat side.
Tighten the knurled screw 7 again, the rubber ring placed on-
to it 6. Tighten the screw against the resistance of the rubber
ring.
Changing the Punch
Loosen the screw 2 and pull the die holder und 4 completely
out of the housing.
Push the punch 3 laterally out of the slot in the die holder 4
and pull it down and out.
Place a new, well greased punch 3 into the slot in the die hold-
er 4 and align it centrally.
Push the die holder 4 with caution over the punch 3 back into
the housing. Turn the die holder into one of the three possible
positions (see “Changing the Cutting Direction”, page 10).
Tighten the screw 2.
If the machine should fail despite the care taken in manufac-
turing and testing procedures, repair should be carried out by
an after-sales service centre for Bosch power tools.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
After-sales Service and Customer Assistance
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Material Max. strength property
[N/mm
2
]
d
max
[mm]
Steel
400 1.6
600 1.0
800 0.7
Aluminium
200 2.0
OBJ_BUCH-480-002.book Page 10 Monday, July 25, 2011 9:39 AM
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch GNA 16 SDS Professional bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch GNA 16 SDS Professional in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 3,84 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info