544232
17
Verklein
Vergroot
Pagina terug
1/209
Pagina verder
English | 17
Bosch Power Tools 1 609 92A 0CV | (4.6.13)
Place the diamond cutting disc 19 onto the mounting
flange 18. The direction arrow on the diamond cutting disc
19 and the direction-of-rotation arrow on the blade guard
6 must correspond.
–Mount the clamping flange 20 and screw in the clamping
bolt 21.
Press and hold the spindle lock 13.
Tighten the clamping bolt 21 (tightening torque 3 –5 Nm)
with the Allen key 22.
Removal of the Diamond Cutting Disc
Press and hold the spindle lock 13.
Remove the clamping bolt 21 with the Allen key 22.
Remove the clamping flange 20 and diamond cutting disc
19 from the drive spindle 17.
Mounting the Hose Kit (see figure BC)
For wet cutting, use only water as the cooling liquid.
Only fasten the hose kit to the power tool using the screw and
the spring washer intended for this purpose.
Screw the hose connection 24 onto the water tap or to the
outlet of a water container. In order to reach the correct water
pressure, the water container must be positioned at least
80 cm above the working surface of the power tool.
Mount connection hose 23 onto hose fitting 5. Check the tight
seating by pulling on the connection hose.
Regulate the outflowing water quantity via water tap 25 be-
fore putting the power tool into operation.
The maximum permissible water pressure is 0.12 MPa.
Operation
Operating Modes
Before any work on the machine itself, pull the mains
plug.
Pre-selecting the Cutting Depth (see figure D)
The cutting depth may only be pre-selected when the
machine is switched off.
Adapt the cutting depth to the thickness of the workpiece. For
optimum results, the diamond cutting disc must protrude ap-
prox. 2 mm out of the material.
Loosen wing bolt 4. For a smaller cutting depth, pull the ma-
chine from the base plate 8; for a larger cutting depth, push
the machine toward the base plate 8. Adjust the desired cut-
ting depth at the cutting-depth scale 3. Tighten wing bolt 4
again.
Adjusting the Cutting Angle (see figure E)
Loosen wing bolt 8. Tilt the machine sidewards until the de-
sired cutting angle is set on the scale 10. Tighten wing bolt 8
again.
Note: For bevel cuts, the cutting depth is smaller than the set-
ting indicated on the cutting-depth scale 3.
0 cutting mark° (see figure F)
The 0° cutting mark (7) indicates the position of the diamond
cutting disc for straight cuts.
Starting Operation
Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Residual Current Device (RCD)
Check the function of the residual current device (RCD) each
time before starting the operation of the tool!
Switch the power tool off.
Insert the mains plug and press the RESET button on the
residual current device (RCD) 14 until the indicator 15
lights up red.
Press the TEST button on the residual current device
(RCD) 14 until the indicator 15 disappears. If the indicator
15 does not disappear, then the residual current device
(RCD) is faulty and must be repaired.Under no circum-
stances work with the power tool!
Once the indicator 15 goes off, press the RESET button
again.
Switch on the machine.
Switching On and Off
To start the machine, press the On/Off switch 2 and keep it
pressed.
To lock the pressed On/Off switch 2, press the lock-on button
1.
To switch off the machine, release the On/Off switch 2 or
when it is locked with the lock-on button 1, briefly press the
On/Off switch 2 and then release it.
Check the diamond cutting discs before use. The dia-
mond cutting disc(s) must be mounted properly and be
able to rotate freely. Carry out a test run for at least one
minute without any load. Do not use diamond cutting
discs that are damaged, out-of-balance, or vibrate.
Damaged diamond cutting discs can rupture and lead to in-
juries.
The protective rubber sleeve of On/Off switch 2 may
not be damaged. The rubber sleeve protects the On/Off
switch 2 against penetrating water and dust.
To save energy, only switch the power tool on when using it.
Working Advice
Do not strain the machine so heavily that it comes to a
standstill.
After heavily straining the power tool, continue to run
it at no-load for several minutes to cool down the acces-
sory.
For cutting-depths greater than 20 mm in hard materi-
als, e.g., concrete, apply several worksteps so that the
motor is not overloaded.
Clamp the workpiece if it does not remain stationary
due to its own weight.
Diamond cutting discs become very hot during opera-
tion; do not touch them until they have cooled down.
Protect the cutting disc against impact, shock and grease. Do
not subject the cutting disc to lateral pressure.
OBJ_BUCH-1810-003.book Page 17 Tuesday, June 4, 2013 1:05 PM
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch GDC 125 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch GDC 125 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 7,68 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info