544269
17
Verklein
Vergroot
Pagina terug
1/270
Pagina verder
English | 17
Bosch Power Tools 1 609 929 W83 | (9.11.10)
Operation
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V
can also be operated with 220 V.
f Before beginning work, consult the struc-
tural engineer, architect or construction
supervisor in charge. Only cut through rein-
forcements with the permission of a struc-
tural engineer.
f When core drilling through walls or floors,
ensure to check the respective rooms/en-
closures for obstructions. Barrier off the
construction site and secure the drilled out
core against falling down with the use of
casing or similar.
Operational Check of the Residual Current
Device
Check the proper function of the residual cur-
rent device 2 each time before working:
Push the “RESET” button on the residual cur-
rent device. The service readiness of the re-
sidual current device is signalled through a
red control indicator.
Push the “TEST” button. The indicator above
the “RESET” button becomes black.
Switching On
Push the “RESET” button on the residual cur-
rent device 2.
Open the water cock 11. Check the flow of wa-
ter at the water-flow indicator 10.
For starting the drilling procedure at half
speed, turn the On/Off switch 13 to the 1/2 po-
sition. The switch cannot be locked in this posi-
tion.
For drilling, turn the On/Off switch 13 to the I
position.
Switching Off
Release the On/Off switch 13 or turn it to the 0
position.
Shut the water cock 11. After finishing work,
disconnect the water outlet connector 3 from
the water supply. Open the water cock 11 and
drain the remaining water.
Adjusting the Speed
Two speed ranges can be preselected with the
gear selector 4.
The two gears are recommended for the follow-
ing bore diameters:
Working Advice
f Before any work on the machine itself, pull
the mains plug.
For drilling, release the lock of the feed handle
5 (see operating instructions of the drill stand).
Start the drilling procedure at half speed
(On/Off switch in the 1/2 position) until the
core bit rotates vibration-free in the material.
Then continue drilling at full speed (On/Off
switch in the I position).
While drilling, adapt the feed pressure to the
material being drilled. Drill with uniform pres-
sure. Lightly pull the core bit out of the bore
from time to time so that the drilling sludge is
removed from the core bit segments.
Do not overload the machine. The control indi-
cator 12 flashes in case of overload (see “Con-
trol Indicator”).
Safety Clutch
If the core bit becomes caught or jammed, the
drive to the drill spindle is interrupted. In this
case, switch the machine off and free the core
bit.
1st gear 82212 mm
2nd gear 32132 mm
OBJ_BUCH-114-002.book Page 17 Tuesday, November 9, 2010 11:58 AM
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch GDB 2500 WE bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch GDB 2500 WE in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 14,6 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info