766863
15
Verklein
Vergroot
Pagina terug
1/241
Pagina verder
English | 15
LED Capacity
Single flash, red 0 − 5%
Charging Guide
Please charge before use.
Charge-control indicator will flash red if:
– Charger is damaged
– Incorrect charger is installed
The tool has overload protection software. If the software is
activated, the tool will lock to prevent damage. To reset the
protection software, connect the charger. Before re-use, we
recommend to fully charge the tool until the charge-control
indicator is continuously green.
Operation
Unlocking (see figure B1)
Deactivate the safety lock (6) by pushing it back. The tool
will open and is now ready for use.
Locking
After usage, close the handles and engage the safety lock (6)
by pushing it forward. Always keep in locked position, when
not in use.
Gripping position (see figures B2–B4)
Grip the tool at the front, as shown. Do not grip the tool to-
wards the back of the handles or with finger(s) between the
handles.
Power-assisted cutting (see figure B)
This tool provides power-assisted cutting. It is operated like
a pair of manual secateurs and will cut in manual mode
without power-assisted cutting until a certain branch dia-
meter is reached. The tool will start power-assisted cutting
when cutting above this branch diameter by starting the in-
tegrated motor. Noise development while power-assisted
cutting is active, is normal.
Power-assist feature is only active as long as gripping force
is exerted on the handles. If no force is exerted onto the
handles, the tool stops.
Working Advice
Pruning tips (see figures C1–C10)
Never operate the tool in an awkward posture. This may
cause serious injury.
Keep your free hand away from the cutting area. Never
touch the blades. They are very sharp and you may cut
yourself.
C1 Always wear protective gloves while pruning.
C2 Never cut too close to the stem so the wound can
heal properly.
C3 Always make the cut about 8mm from the bud.
C4 The cut should slope away from the bud so the rain
can run off.
C5 If you remove an entire stem, cut back to the point
where it branched.
C6 Never push the blade of the pruner into the ground to
cut root suckers.
C7 Cut branches one by one as shown.
C8 Remove overcrowds or crossing stems.
C9 Remove thin or weak growth.
C10 Always remove dead, damaged and diseased
branches.
Troubleshooting
The following table provides common troubleshooting information. The battery-charge control indicator provides additional
information that can be used to identify a malfunction or problem.
Problem Possible Cause Corrective Measure
Tool stops while cutting Not enough pressure on handles Continue moving handles towards each other
while cutting.
Hold the tool with a firmer grip.
Blades get stuck in a thick
branch Low battery capacity
Too hard wood
Too big diameter
Wrong cutting position
Grip the upper handle only and remove the tool
by tilting the blade.
Recharge tool, if necessary.
Power-assisted cutting does not activate with LED flashing when cutting is attempted:
LED flashes red 3 times Wood being cut is too thick/hard Try cutting in a thinner area of the branch.
Bosch Power Tools F 016 L94 019 | (04.03.2020)
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch EasyPrune bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch EasyPrune in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 4,83 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info