Handleiding Bosch AdvancedTableCut 52 (pagina 25 van 305) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors)

766874

Verklein

Vergroot

Pagina terug

1/305

Pagina verder

English | 25

Operation

Supporting the Workpiece/Using an Underlay

The free end of long workpieces must have something

placed underneath it or be supported.

– Position the workpiece support (34) on the work bench

underneath the free end of the workpiece such that it is

supported (see figure G1).

– You can also support the workpiece by placing the Bosch

PTA 1000 roller support stand under its free end (see fig-

ure G2). The rollers ensure that the workpiece can move

accordingly.

Setting Mitre Angles (Universal Guide) (see

figureH)

The mitre angle can be set between 60° (left side) and 60°

(right side).

For quick and precise setting of commonly used mitre

angles, the universal guide(2) clicks into place at the follow-

ing standard angles:

Left Right

0°

60°; 45°; 30°; 22.5°; 15° 15°; 22.5°; 30°; 45°; 60°

– Loosen the clamping lever(1) by turning it anticlockwise.

– Turn the universal guide(2) until the required mitre angle

engages or the angle indicator(35) shows the required

mitre angle on the scale(36).

– Re-tighten the clamping lever(1).

Note: Use the screw grabber(37) to make it easier to

tighten and loosen the clamping lever.

Setting the Bevel Angle (Saw Blade)

The bevel angle can be set between 0° and 45°.

– Loosen the wing bolt (17) slightly by turning it anticlock-

wise.

– Turn the rotary knob (15) until the angle indicator (16)

shows the desired bevel angle on the scale (14).

– Retighten the wing bolt (17).

Note: Use the screw grabber (37) to make it easier to

tighten and loosen the wing bolt.

Adjusting the Universal Guide

uBefore making any cuts, first make sure that the saw

blade cannot come into contact with the stops or any

other parts of the tool at any time.

The universal guide (2) can be used in different ways ac-

cording to the operating mode:

– As a cross, angle or parallel guide

Using the Universal Guide as a Cross or Angle Guide (see

figureI1)

– Mount the universal guide(2) on the saw table(5).

Pull-push saw operation: Fully insert the universal guide

into the middle guide groove(25).

Table saw operation: Mount the universal guide in the

right or left guide groove(25).

– If required, mount the additional stop(21) on the univer-

sal guide(2).

– Set the required horizontal mitre angle.

– Set the required bevel angle.

– Check whether the stops are outside the cutting area.

– If required, loosen the two wing bolts(27), move the ad-

ditional stop(21) and re-tighten the two wing bolts(27).

Note: To prevent the workpiece from slanting or slipping,

the distance between the saw blade(3) and the additional

stop(21) must not be more than 15mm.

Using the Universal Guide as a Parallel Guide (see

figureI2)

–Table saw operation: Mount the universal guide(2) on

the left or right in the guide groove(24) on the saw

table(5) (see "Mounting the universal guide (see figure

A)", page23).

– Mount the additional stop(21) on the universal guide(2)

(see "Mounting the additional stop (see figure B)",

page23).

Note: During sawing, workpieces may become trapped

between the universal guide and the saw blade, or be

caught and flung away by the saw chain as it rises.

Ensure that the additional stop(21) is mounted correctly.

– Set a mitre angle of 0°(see "Setting Mitre Angles (Univer-

sal Guide) (see figureH)", page25).

– Loosen the knurled screw(19) and move the universal

guide(2) by the required distance.

– Re-tighten the knurled screw(19).

Start-up

uProducts that are only sold in AUS and NZ: Use a resid-

ual current device (RCD) with a nominal residual current

of 30 mA or less.

uPay attention to the mains voltage. The voltage of the

power source must match the voltage specified on the

rating plate of the power tool. Power tools marked

with 230V can also be operated with 220V.

Switching On/Off

–Switch on the power tool by pressing the green on button

(13).

–Switch off the power tool by pressing the red off button

(12).

Power Outage

The on/off switch acts as a zero-voltage switch that prevents

the power tool from starting up again following a power out-

age (e.g. if the mains plug is removed during operation).

To restart the power tool following a power outage, press the

green on button (13) again.

Bosch Power Tools 1 609 92A 66E | (12.01.2021)

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Bosch AdvancedTableCut 52 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info