Handleiding Bosch AdvancedGrind 18 SystemBox (pagina 24 van 323) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors)

766843

Verklein

Vergroot

Pagina terug

1/323

Pagina verder

24 | English

uThe rated speed of the accessory must be at least

equal to the maximum speed marked on the power

tool. Accessories running faster than their rated speed

can break and fly apart.

Practical advice

uExercise caution when cutting slots in structural walls;

see the "Information on structural design" section.

uClamp the workpiece if it is not secure under its own

weight.

uDo not load the power tool so heavily that it comes to a

stop.

uIf the power tool has been subjected to a heavy load,

continue to run it at no-load for several minutes to

cool down the accessory.

uDo not use the power tool with a cut-off stand.

uDo not touch grinding and cutting discs until they have

cooled down. The discs can become very hot while work-

ing.

Rough grinding

uNever use cutting discs for rough grinding.

The best rough grinding results are achieved with a set angle

of 30° to 40°. Move the power tool back and forth with mod-

erate pressure. This will ensure that the workpiece does not

become too hot or discolour and that grooves are not

formed.

Flap disc

The flap disc (accessory) enables you to machine curved

surfaces and profiles.

Flap discs have a considerably longer service life, lower

noise levels and lower sanding temperatures than conven-

tional grinding discs.

Cutting metal

uAlways use the protective guard for cutting (13) when

cutting with bonded abrasives.

When carrying out abrasive cutting, use a moderate feed

that is suited to the material being machined. Do not exert

pressure on the cutting disc and do not tilt or swing the

power tool.

Do not attempt to reduce the speed of a cutting disc coming

to a stop by applying pressure from the side.

The power tool must always

work in an up-grinding mo-

tion. Otherwise there is a

risk that it will be pushed

uncontrolled out of the cut.

For best results when cut-

ting profiles and rectangular

tubing, start at the smallest

cross section.

Cutting Stone (see figure A)

uProvide sufficient dust extraction when cutting stone.

uWear a dust mask.

uThe power tool may be used only for dry cutting/grind-

ing.

For best results when cutting stone, use a diamond cutting

disc.

When using the extraction guard for cutting with a cutting

guide (24), the vacuum cleaner must be approved for vacu-

uming stone dust. Suitable vacuum cleaners are available

from Bosch.

Switch on the power tool

and position it with the

front part of the cutting

guide on the workpiece.

Move the power tool with a

moderate feed motion that

is suited to the material be-

ing machined.

When cutting especially

hard materials such as con-

crete with a high pebble content, the diamond cutting disc

can overheat and become damaged as a result. This is

clearly indicated by circular sparking, rotating with the dia-

mond cutting disc.

If this happens, stop cutting and allow the diamond cutting

disc to cool down by running the power tool for a short time

at maximum speed with no load.

If work is noticeably slower and with circular sparking, this

indicates that the diamond cutting disc that has become

dull. You can resharpen the disc by briefly cutting into abras-

ive material (e.g. lime-sand brick).

Information on structural design

Slots in load-bearing walls are subject to DIN 1053 part 1 or

country-specific regulations. These regulations must be ob-

served under all circumstances. Seek advice from the re-

sponsible structural engineer, architect or construction su-

pervisor before starting work.

Recommendations for optimal handling of the battery

Protect the battery against moisture and water.

Only store the battery only within a temperature range of -20

to 50 °C. Do not leave the battery in your car in the summer,

for example.

Occasionally clean the ventilation slots on the battery using a

soft brush that is clean and dry.

A significantly reduced operating time after charging indic-

ates that the battery has deteriorated and must be replaced.

Follow the instructions on correct disposal.

Maintenance and Service

Maintenance and Cleaning

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

1 609 92A 6D6 | (25.06.2021) Bosch Power Tools

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Bosch AdvancedGrind 18 SystemBox Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info