707735
20
Verklein
Vergroot
Pagina terug
1/227
Pagina verder
20 | English
1 609 92A 4BE | (07.09.2018) Bosch Power Tools
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
Provide for good ventilation of the working place.
It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
u Avoid dust accumulation at the workplace. Dust can
easily ignite.
Operation
Starting Operation
Inserting the battery
Push the charged battery (9) into the base of the power tool
from the rear until the battery is securely locked.
Setting the rotational direction
The electronic rotational direction switch (7) is used to
change the rotational direction of the power tool. However,
this is not possible while the on/off switch (14) is being
pressed.
Setting right rotation (see figure I)
To drill and drive in screws, push the electronic rotational
direction switch (7) down.
The rotational direction indicator for right rotation
(5) lights up when the on/off switch (14) is
pressed, the rotational direction switch (7) is
pressed and the motor is running.
Setting left rotation (see figure J)
To loosen or undo screws and nuts, push the electronic rota-
tional direction switch (7) down.
The rotational direction indicator for left rotation
(6) lights up when the on/off switch (14) is
pressed, the rotational direction switch (7) is
pressed and the motor is running.
Preselecting the torque
The torque presetting ring (3) can be used to preselect the
required torque in 20 stages and "MAX". Once the set torque
has been reached, the application tool will be stopped.
Setting the operating mode (see figure K)
u Only operate the mode selector switch (4) when the
power tool is not in use.
You can pre-select two speed ranges with the mode selector
switch (4).
Screwdriving mode (first screw phase):
Low speed range; for screwdriving or working with a large
drilling diameter.
Drilling/impact drilling mode (second screw phase):
High speed range; for working with a small drilling diameter.
Screwdriving
Set the torque presetting ring (3) to the re-
quired torque.
Set the mode selector switch (4) to the
"screwdriving" symbol.
Drilling
Set the torque presetting ring (3) to "MAX".
Set the mode selector switch (4) to the
"drilling" symbol.
Impact drilling (AdvancedImpact 18)
Set the torque presetting ring (3) to "MAX".
Set the mode selector switch (4) to the "im-
pact drilling" symbol.
Switching on/off
To start the power tool, press and hold the on/off switch
(14).
The light (12) lights up when the on/off switch (14) is lightly
or fully pressed, meaning that the work area is illuminated in
poor lighting conditions.
To switch off the power tool, release the on/off switch (14).
Adjusting the Speed
You can adjust the speed of the power tool when it is on by
pressing in the on/off switch to varying extents.
Applying light pressure to the on/off switch results in a low
rotational speed. Applying increasing pressure to the switch
increases the speed.
Fully automatic spindle lock (Auto-Lock)
The drill spindle, and therefore the tool holder, are locked
when the on/off switch (14) is not pressed.
This allows screws to be driven in even when the battery is
discharged and enables the power tool to be used as a
screwdriver.
Temperature-dependent overload protection
In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or the permitted bat-
tery temperature is exceeded, the electronics of the power
tool will switch off until the temperature returns to within the
optimum operating temperature range.
The three LEDs in the battery charge indicator (13) and the
PowerLight (12) flash quickly when the temperature of the
battery is outside the operating temperature range of –20 to
+50 °C and/or the overload protection has been triggered.
Protection against deep discharge
The lithium-ion battery is protected against deep discharge
by the Electronic Cell Protection (ECP). When the battery is
discharged, the power tool is switched off by means of a pro-
tective circuit: The application tool no longer rotates.
Working Advice
u Only apply the power tool to the screw when the tool
is switched off. Rotating application tools can slip off.
20

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Bosch-AdvancedDrill-18

Zoeken resetten

  • bij het indrukken van de schakelaar knipperen alle drie de led's maar draait de machine niet
    batterij is opgeladen en werkt bij andere machines wel Gesteld op 21-11-2023 om 13:21

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch AdvancedDrill 18 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch AdvancedDrill 18 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 18,34 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info