697454
48
Verklein
Vergroot
Pagina terug
1/170
Pagina verder
48 en | Settings AMAX panel
2019.08 | 11 | F.01U.309.277 Installation Manual Bosch Security Systems B.V.
RPC gets the Subscriber ID, IP address and port from the UDP data packets (IP No. and Port
is parsed from UDP data packet).
RPC with running RPS (Remote Programming Software = A-Link Plus) saves the received UDP
data packet information into its own RAM, the information is lost after RPS is closed.
When a connection is started and the IP address set in the customer information doesn’t
match with the IP Address from the RAM, the A-Link Plus opens a window to ask if the new IP
Address and Port should be used.
When RPS is opened, a connection can only be established when the IP address and port
number of the AMAX panel have not changed, after RPS received previous data.
If the IP address has changed RPC with running RPS must wait for the next UDP Data package
send from the Panel. When the connection is established, the AMAX panel sends a polling
telegram of 25 bytes.
6.1.8 Call back and domestic call
Call back telephone number
This address stores the telephone number to call when upload / download is requested or the
user enters his code + [5] [7] and presses [#] to initiate a modem call from the AMAX panel to
establish a communication link with the remote computer. The computer must be running
remote programming software A-Link Plus and must be set to waiting for an incoming call. The
call back telephone number is also necessary if remote connect with call back verification is
required.
Domestic call
Four recordable voice messages for four dialing telephone numbers are supported. Each of the
four recordable voice messages can take up to 9 seconds. The voice messages are recorded
with the tool “Rec.exe” that comes with A-Link Plus and are transferred via A-Link Plus to the
AMAX panel. They can only be transferred via USB or network connection. The supported
format of the voice message files is the following:
For firmware version up to 1.4: .wav
For firmware version 1.5 and higher: .va3
When the AMAX panel is activated into zone tamper / zone alarm, the programmed telephone
number is dialed and the recorded voice message is played.
All alarm events only need one report / acknowledgement.
The transmission sequence is repeated until the AMAX panel receives an acknowledgement
tone.
The AMAX panel automatically hangs up after about 45 seconds if it cannot detect the
acknowledgement tone and redial later.
The user presses any key on the telephone between two acknowledgement tones to confirm
the alarming.
The acknowledgement tone is the DTMF signal sent by the remote user with any key ([0] - [9]
or [*] or [#]).
If the AMAX panel received the acknowledgement from the user, it will send a 2 seconds long
confirmation beep as an acknowledge tone and hang up the line.
6.1.9 Ring times
Ring Count
This function defines the number of rings before the AMAX panel answers an incoming call. It
is necessary to enable remote arming and remote upload/download to use this function.
48

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch AMAX panel 4000 EN bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch AMAX panel 4000 EN in de taal/talen: Engels als bijlage per email.

De handleiding is 2,95 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Bosch AMAX panel 4000 EN

Bosch AMAX panel 4000 EN Snelstart handleiding - Nederlands - 76 pagina's

Bosch AMAX panel 4000 EN Installatiehandleiding - Nederlands - 190 pagina's

Bosch AMAX panel 4000 EN Snelstart handleiding - Deutsch - 76 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info