Handleiding Bort BSS-1800N-ECO (pagina 8 van 24) (Engels)

555077

Verklein

Vergroot

Pagina terug

1/24

Pagina verder

STORAGE OF THE CLEANER

1. Upon the completion of the operation of the cleaner,

turn off its power supply, and pull the power plug out of

the power socket, then step on the cord reeling button

to reel in the power cord fully. Hang the ﬂ oor brush onto

the ﬂ oor brush hook, as is shown in Figure (7).

1. Place the cleaner in the dry indoor environment.

CLEANING OF THE DUST BARREL

Remove the rubbish in the dust barrel frequently to

avoid the failure of the cleaner.

1. Clean the dust barrel only after the power plug of the

cleaner has been pulled out;

2. Put the dust barrel over the rubbish bin (bag), press

down the releasing button of the dust barrel, the bottom

cover of the dust barrel will automatically fall down, and

clear and empty the dust barrel, as is shown in Figure

(8).

Cleaning of front ﬁ lter for motor:

Warning: please make sure the power supply of

the cleaner has been cut off before carrying out the

following steps:

1. Pull out the power cord plug of the cleaner from the

power socket.

2. Press down the handle of the dust barrel to remove

the dust barrel, and remove the cover of the front ﬁ lter

for motor, and then use the brush to clean the ﬁ lter

(sponge and ﬁ lter gauze with composite coating) or

place it under the cock to clean, as is shown in Figure

(9/10).

Caution:

It is normal that the white central ﬁ lter in the dust barrel

may change color, which cannot affect its ﬁ ltration

performance. If the hose and the central ﬁ lter are

difﬁ cult to clean, we recommend that you use water to

ﬂ ush them; however, please be sure to place them in

the dry air for at least 24 hours after they are ﬂ ushed

by water.

Key Points:

Please note: when the dust collecting barrel or the ﬁ lter

cover is not installed in place, the operation status will

be invalid, and the cleaner will have no dust absorption

capacity. At this time, you need to check carefully

whether the dust collecting barrel and the ﬁ lter cover

have been installed in place.

Caution: please keep the suction passage unobstructed,

otherwise the motor may become overheating or even

be damaged.

REPLACEMENT OF REAR FILTER

FOR MOTOR

The rear ﬁ lter for motor is installed behind the air outlet

grid, which can be washed due to the materials used.

When the surface is jammed seriously by dust, the ﬁ lter

should be replaced by a new one or washed by water

to maintain enough suction force. (Figure 11/12)

It is usually necessary to clean and replace the ﬁ lters

for motor only after they have been used for 6 months

to 12 months. Please remember to conﬁ rm that all

ﬁ lters have been correctly installed into the machine

before turning on the cleaner to use.

handle is pressed down to the bottom, the dust barrel

can be lifted to remove.

ASSEMBLY OF METAL EXTENSION PIPE

AND FLOOR BRUSH

Insert the front end of the hose handle into the metal

extension pipe according to Figure (5); then insert

the other end of the metal extension pipe into the

rounded inlet of the ﬂ oor brush, and adjust to the

proper direction. At this time, the assembly of the whole

machine is completed.

OPERATION INSTRUCTIONS

HOW TO START

1. First of all, pull out the power cord from the cord reel

to the needed length; insert the power cord plug into

the power socket, and press down the power switch

button with ﬁ nger or step on it with foot; then you can

control the start and stop of the cleaner.

2. The yellow mark on the power cord indicates its

desired length. Never pull out the power cord to the

length exceeding the red mark.

CONTROL OF SUCTION FORCE

When the suction inlet is jammed by some cloth due

to the over-large suction force, you can adjust the air

escape pushbutton on the hose handle to control the

suction force at the suction inlet, as is shown in Figure

(6).

PROTECTIVE DEVICES OF MOTOR

1. There is a temperature controller designed in the

body of cleaner motor, which can automatically cut

off the power supply of motor to prevent overheating.

When the air-inlet or air-outlet pipe is overloaded or

blocked, the temperature of motor rises, then the

temperature controller cuts off the power supply of

motor automatically to make the motor cool, preventing

the cleaner from being damaged.

2. If the temperature controller is cut off, stop the

cleaner immediately and pull out the power plug to

make the cleaner cool, and check and remove the

hair roll or other roll-like rubbish blocking the air inlet

(including the hose and the spile), and replace the ﬁ lter

HEPA or ﬁ lter gauze when necessary.

3. After cooling the motor for 30mins, plug in the power

plug and check whether the temperature controller has

been reset. If the power supply of the cleaner hasn’t

been cut off, the temperature controller of the motor

won’t be reset even when the motor has become cool.

MAINTENANCE OF THE CLEANER

All the day-to-day maintenance and repair jobs should

be done after the power plug has been pulled out.

2. Frequently remove the rubbish from the dust barrel,

so as to avoid the failure of the cleaner.

3. Never wipe the surface of the cleaner with gasoline

or oily liquid. Wipe it with water or neutral detergent.

Caution: be sure to wring out the wiping cloth dry for

wiping, it is prohibited for water to inﬁ ltrate into electrical

elements of the cleaner.

3. When the cleaner is placed idle not in use, it should

not be put directly in the sun or in a damp place.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Bort BSS-1800N-ECO Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info