Handleiding Bomann ES 1185 CB (pagina 56 van 98) (Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Pools)

651946

Verklein

Vergroot

Pagina terug

1/98

Pagina verder

ES1185CB_IM 04.03.16

Making Espresso

CAUTION:

Do not brew an espresso when the appliance is still under

pressure (for example when milk has been frothed earlier).

With too much pressure in the appliance, espresso leaks

at the edge of the brewing head. That may lead to a faster

wearing of the rubber seal.

1. Switch the appliance on. The status indicator lamp “I”

lights up. The appliance starts heating up. The warming

plate (13) heats up.

NOTE:

• Use the warming plate to pre-heat your cup(s).

• If you want to pre-heat the cup(s) more rapidly, rinse

them with hot water.

2. Make sure that the drip tray (7) and the drip tray grid (6)

are inserted.

3. Fill the water tank with the desired amount of clean, fresh

water. The water level must be between the MIN and

MAX markings. Close the lid again.

4. If you frothed milk earlier, completely release the pressure

from the appliance:

4.1. The switches (9) and (10) must be set to the posi-

tion ““.

4.2. Set a suitable vessel under the steam nozzle.

4.3. Turn the steam volume control (3) slowly in the

direction “+“ until no steam comes out any longer.

4.4. Close the steam volume control by turning it in the

direction “OFF”.

5. Select a lter insert (14 / 15). Place the insert in the lter

holder. Ensure that the lter safeguard is not upright.

6. Fill the lter insert with espresso grounds. Use the sup-

plied measuring spoon (18). Observe the MAX marking in

the lter insert. Spread the espresso grounds evenly and

push down slightly with the tamper (18). Clean the edge

of the lter holder.

7. Attach the lter holder to the group head. Ensure that the

lter holder is properly attached in the group head.

8. The necessary brewing temperature is reached as soon

as the indicator lamp “ok” lights up. Place your pre-heat-

ed cup(s) under the group head exactly on the two holes

you can see in the drip tray grid.

9. Turn on the pump with the switch (9). The hot water is

forced through the lter.

NOTE:

This process does not end automatically!

10. Stop the brewing process by turning off the pump when

the desired amount of espresso is in your cup(s).

11. Remove the cup(s).

NOTE:

Remove the lter holder every time after making es-

presso. In this way you extend the lifetime of the group

head’s rubber seal.

12. Remove the lter holder from the group head.

13. Empty and rell the lter to brew another cup of espresso:

WARNING:

Metal parts of lter holder and lter insert are hot.

a) Flap the lter safeguard

(17) up. Push the lter

safeguard with your thumb

towards the lter insert

while turning the lter

holder around (see Fig.).

b) Tap the coffee grounds out of the lter insert. Use

a spoon, if necessary. Rinse the remaining coffee

grounds with hot water out of the lter insert.

14. To prepare the next cup(s) of espresso, proceed as

described above.

Making Cappuccino

Generally cappuccino consists of one-third coffee, one-third

hot milk and one-third frothed milk.

The milk froth should not be rm enough to be shaped with a

spoon. It should be creamy, such as not completely whipped

cream, of a viscous texture.

For the preparation you need in addition

• a larger, bellied cup (approx. 180 ml), in which you make

the espresso,

• a small frothing jug with spout (e.g. 0.3 ℓ),

• a small, heat-resistant container,

• cold milk with at least 3.5 % fat content.

CAUTION: Observe the sequence!

1. Brewing of espresso.

2. Frothing milk.

For preparation of cappuccino, proceed as described under

“Making Espresso”.

Froth the milk as follows:

WARNING: Danger of scalding!

Escaping steam can cause injuries. During the heating

process hot steam / water can escape from group head

and / or steam nozzle!

• Ensure that the steam control knob (3) is set to “OFF”

position before activating the steam function.

• Do not direct the steam nozzle towards persons.

• Always place a container under the steam nozzle (4).

1. Ensure that the switch (9) is in “” position.

2. Swivel out the steam nozzle (4). Attach the steam nozzle

cover all the way on the steam nozzle.

3. Place a heat-resistant container under the steam nozzle.

4. Fill the jug half with cold milk.

5. Set the switch (10) to the position “

“. Wait until the

indicator lamp “ok” lights up.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Bomann ES 1185 CB Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info