Program Time (min.)**17162-8082-105124-155127-163109-125
Water Consumption (lt)1010,410,41014,216,2
Power Consumption (kWh)0,91,101,141,051,421,50
Average consumption values are valid for 15°C water inlet temperature and 21°C ambient temperature. Values stated on the markings of the product or in the printed
documents accompanying the product are obtained in the laboratory on basis of the relevant standards. These values may change according to the usage and ambient
conditions of the product.
* Reference programme for testing institutes. The tests in accordance with EN 50242 must be carried out with a full water softener salt dispenser and a full rinse aid reservoir,
and using the test programme.
** The first period indicates the time remaining after the program is determined and the second period indicates the total time elapsed after the program has started.
32
EN
1. Turn the micro filter (3) and
coarse filter (2) assembly counter
clockwise and pull it out from its
seating (A).
6
Maintenance and cleaning
Service life of the product extends and
frequently faced problems decrease if it
is cleaned at regular intervals.
A Unplug the product and turn off the
tap before attempting any cleaning
procedures.
CDo not use abrasive substances for
cleaning.
CClean the filters and impellers at
least once a week.
Cleaning the outer surface of
the product
Clean the outer surface and door
gaskets of the product gently with a mild
cleaning material and damp cloth. Wipe
the control panel only with a damp cloth.
Cleaning the interior of the
machine
Clean the interior of the machine
and the tank by running a prewash
programme without detergent or
a long washing programme with
detergent based on the degree of
soiling.
If water has remained in the
machine, drain the water by
performing the procedures under
the topic "Canceling a programme".
If the water cannot be discharged,
clean any leftover deposits that
have piled up in the bottom of the
machine, blocking the water path.
Cleaning the filters
Clean the filters at least once a week
in order for the machine operates
efficiently. Check if food residues are left
on the filters. If there are food residues
on filters, take them out and clean well
under running water.
1031
2. Pull out the metal / plastic filter (1)
(B).
33
EN
4. Clean all three filters under tap water
by means of a brush.
5. Replace the metal/plastic filter.
6. Place the coarse filter into the
microfilter. Make sure that it is
properly seated. Turn the coarse
filter clockwise until a “click” sound is
heard.
A Do not use the dishwasher without
filter.
CIncorrect placement of the filters will
reduce washing efficiency.
Cleaning the hose filter
Damages on the machine that may be
caused by impurities coming from the
urban supply water or your own water
installation (such as sand, dirt, rust, etc.)
can be prevented by means of the filter
attached to the water inlet hose. Check
the filter and the hose regularly and
clean them if necessary.
1. Turn off the tap and remove the
hose.
2. After taking out the filter, clean it
under running tap water.
3. Place the cleaned filter back to its
seat in the hose.
4. Install the hose to tap.
3. Press the two pawls on the coarse
filter inwards and separate the
coarse filter from the assembly (C).
Cleaning the impellers
Clean the impellers at least once a
week in order for the machine operates
efficiently.
Lower impeller
Check if the holes on the lower impeller
(1) are clogged. If they are clogged,
remove and clean the impeller. Pull the
lower impeller up to remove it (A, B).
34
EN
1032
Upper impeller
Check if the holes on the upper
impeller (2) are clogged. If they
are clogged, remove and clean the
impeller. Turn its nut to left to remove
the upper impeller (C, D).
Make sure that the nut is tightened well
when installing the upper impeller.
35
EN
Troubleshooting
Machine does not start.
• Power cable is unplugged. >>> Check if the power cable is plugged in.
• Fuse is blown. >>> Check the fuses in your house.
• Water is cut. >>> Make sure that the water inlet tap is open.
• Door of the machine is open. >>> Make sure that you have closed the door
of the machine.
• On / Off button is not pressed. >>> Make sure that you have turned on the
machine by pressing the On / Off button.
Dishes are not washed clean
• Dishes are not placed orderly in the machine. >>> Load the dishes as
described in the user manual.
• Selected programme is unsuitable. >>> Select a programme with a higher
temperature and cycle time.
• Impellers are stuck. >>> Prior to starting the programme, turn the lower and
upper impellers by hand to make sure that they rotate freely.
• Impeller holes are clogged. >>> Lower and upper impeller holes might
be clogged with food remnants such as lemon pips. Clean the impellers
regularly as illustrated in section "Cleaning and Care".
• Filters are clogged. >>> Check if the filter system is clean. Clean the filter
system regularly as illustrated in section "Cleaning and Care".
• Filters are installed incorrectly. >>> Check the filter system and make sure
that it is installed correctly.
• Baskets are overloaded. >>> Do not overload the baskets in excess of their
capacity.
• Detergent is stored under unsuitable conditions. >>> If you are using powder
detergent, do not store the detergent package in humid places. Keep it in a
closed container if possible. For ease-of-storing, we recommend you to use
tablet detergents.
• Detergent is not sufficient. >>> If you are using powder detergent, adjust
the amount of detergent according to the soiling degree of your dishes and/
or programme definitions. We recommend you to use tablet detergents for
optimum results.
• Rinse aid is not sufficient. >>> Check the rinse aid indicator and add rinse
aid if necessary. Increase the rinse aid setting if there is enough amount of
rinse aid in the machine.
• Detergent dispenser lid is left open. >>> Make sure that the detergent
dispenser lid is closed tightly after adding detergent.
7
36
EN
Dishes are not dry at the end of cycle
• Dishes are not placed orderly in the machine. >>> Place your dishes in a
way that no water will accumulate in them.
• Rinse aid is not sufficient. >>> Check the rinse aid indicator and add rinse
aid if necessary. Increase the rinse aid setting if there is enough amount of
rinse aid in the machine.
• Machine is unloaded right after the programme is over. >>> Do not unload
your machine right after washing process is completed. Slightly open the
door and wait for evacuation of the steam inside for a while. Unload the
dishes after the pieces cool down to a touchable level. Start unloading
process from the lower basket. Thus, dropping of water remained on a piece
at upper basket onto the pieces at lower basket is prevented.
• Selected programme is unsuitable. >>> Since rinsing temperature is low at
programmes with short duration, drying performance will also be low. Select
programmes with longer duration for a higher drying performance.
• Surface quality of the kitchen utensils is deteriorated. >>> Desired washing
performance can not be obtained at kitchen utensils with deteriorated
surfaces and it is not suitable to use such utensils in terms of hygiene
as well. Also, water can not flow easily on deteriorated surfaces. It is not
recommended to wash such kitchen utensils in dishwasher.
CIt is normal that drying complaints can be experienced with Teflon kitchen
utensils. It is associated with the structure of Teflon. Since the surface
tensions of Teflon and water are different, water droplets will remain as
beads on the Teflon surface.
Tea, cafe or lipstick stains remain on dishes.
• Selected programme is unsuitable. >>> Select a programme with a higher
temperature and cycle time.
• Surface quality of the kitchen utensils is deteriorated. >>> Tea and cafe
stains or other dye spots may not be cleaned in dishwasher when they
have penetrated in deteriorated surfaces. Desired washing performance
can not be obtained at kitchen utensils with deteriorated surfaces and it
is not suitable to use such utensils in terms of hygiene as well. It is not
recommended to wash such kitchen utensils in dishwasher.
• Detergent is stored under unsuitable conditions. >>> If you are using powder
detergent, do not store the detergent package in humid places. Keep it in a
closed container if possible. For ease-of-storing, we recommend you to use
tablet detergents.
37
EN
Lime traces remain on dishes and glassware gains a misty appearance
• Rinse aid is not sufficient. >>> Check the rinse aid indicator and add rinse
aid if necessary. Increase the rinse aid setting if there is enough amount of
rinse aid in the machine.
• Water hardness setting is low or salt level is insufficient >>> Measure the
hardness of the supply water appropriately and check the water hardness
setting.
• Salt leakage exists. >>> Pay attention not to spill salt around the salt filling
hole while adding salt. Make sure that the salt reservoir lid is tightly closed
after finishing the filling process. Run the prewash programme to remove the
salt that spilled inside the machine. Since the salt granules that will remain
under the lid will dissolve during prewash, causing the lid loosen, check the
lid once again at the end of the programme.
There is a different odour in the machine
CA new machine has a peculiar odour. It will fade out after a couple of
washing.
• Filters are clogged. >>> Check if the filter system is clean. Clean the filter
system regularly as illustrated in section "Cleaning and Care".
• Dirty dishes are kept in dishwasher for 2-3 days. >>> If you are not going
to start the machine right after you have put the dishes into it, remove
the remnants on the dishes and run the Prewash programme without
detergent every 2 days. In such cases, do not close the door of the machine
completely in order to avoid odour build up in machine. You can also use
commercially available odour removers or machine cleaners.
38
EN
Rust, discoloration or surface deterioration occurs on dishes
• Salt leakage exists. >>> Salt may cause deterioration and oxidation on
metal surfaces. Pay attention not to spill salt around the salt filling hole
while adding salt. Make sure that the salt reservoir lid is tightly closed after
finishing the filling process. Run the prewash programme to remove the salt
that spilled inside the machine. Since the salt granules that will remain under
the lid will dissolve during prewash, causing the lid loosen, check the lid
once again at the end of the programme.
• Salty food remnants have remained on dishes for a long time. >>> If
silverware soiled with such foods will be kept waiting in machine, dirt must
be removed by prewash or dishes must be washed without being kept
waiting.
• Electric installation is not grounded. >>>Check if your machine is connected
to the actual grounding line. Otherwise, the static electric created in the
product causes arcs on the surfaces of metal items creating pores, removing
the protective cover on the surface and causing discoloration.
• Intensive cleansers such as bleaches are used. >>> Protective cover on
metal surfaces gets damaged and looses its efficiency in time when it gets in
contact with cleansers such as bleach. Do not wash your dishes with bleach.
• Metal items particularly such as knives are used for purposes other then
their intended uses. >>> Protective cover on the edges of knives may get
damaged when they are used for purposes such as opening cans. Do not
use metal kitchen utensils out of their intended uses.
• Silverware are made of low quality stainless steel. >>> Corrosion on such
items is inevitable; they should not be washed in dishwashers.
• Kitchen utensils that are already corroded are washed in dishwasher.
>>> Rust on a corroded item can migrate to other stainless steel surfaces
and cause corrosion on those surfaces as well. Such items should not be
washed in dishwashers.
39
EN
Detergent remains in detergent dispenser.
• Detergent dispenser was damp when adding detergent. >>> Make sure that
the detergent dispenser is dried well prior to filling it with detergent.
• Detergent is added long before the washing process. >>> Pay attention to
add detergent shortly before start-up of the washing.
• Opening of the detergent dispenser lid is prevented during washing. >>>
Place the dishes in a way that will not prevent the detergent dispenser lid
from opening and the water going into the machine from impellers.
• Detergent is stored under unsuitable conditions. >>> If you are using powder
detergent, do not store the detergent package in humid places. Keep it in a
closed container if possible. For ease-of-storing, we recommend you to use
tablet detergents.
• Impeller holes are clogged. >>> Lower and upper impeller holes might
be clogged with food remnants such as lemon pips. Clean the impellers
regularly as illustrated in section "Cleaning and Care".
Decorations and ornaments on kitchen utensils are being erased.
CDecorated glasses and decorated luster porcelains are not suitable for
washing in the dishwasher. Manufacturers of glassware and porcelain
tableware items do not recommend washing such kitchen utensils in the
dishwashers either.
Dishes are scratched.
CKitchen utensils that contains or are made of aluminum should not be
washed in dishwasher.
• Salt leakage exists. >>> Pay attention not to spill salt around the salt filling
hole while adding salt. Spilled salt can cause scratches. Make sure that
the salt reservoir lid is tightly closed after finishing the filling process. Run
the prewash programme to remove the salt that spilled inside the machine.
Since the salt granules that will remain under the lid will dissolve during
prewash, causing the lid loosen, check the lid once again at the end of the
programme.
• Water hardness setting is low or salt level is insufficient >>> Measure the
hardness of the supply water appropriately and check the water hardness
setting.
• Dishes are not placed orderly in the machine. >>> When placing the glasses
and other glassware into the basket lean them not against other dishes but
the edges or racks of the basket or the glass support wire. Striking of the
glasses to each other or to other dishes due to the impact of water during
washing can cause breaks, or scratches on their surfaces.
40
EN
A smear remains on glasses that resembles milk stain which can not be
removed when wiped by hand. A bluish / rainbow appearance occurs when
the glass is pointed to light.
• Excessive rinse aid is used. >>>Lower rinse aid setting. Clean the spilled
rinse aid when adding rinse aid.
• Corrosion has occurred on glass due to soft water. >>> Measure the
hardness of the supply water appropriately and check the water hardness
setting. If your supply water is soft (<5 dH), do not use salt. Choose
programmes that wash in higher temperatures (e.g. 60-65°C). You can also
use glass protective detergents that are commercially available.
Foam forms in the machine.
• Dishes are washed with hand-wash detergent by hand but not rinsed before
placing them into the machine. >>> Hand-wash detergents do not contain
antifoam. There is no need to hand-wash the dishes before placing them into
the machine. Removing the coarse soil on the dishes under tap water, with a
tissue paper or fork will be sufficient.
• Rinse aid has spilled into the machine when adding rinse aid. >>> Take care
that rinse aid is not spilled in the machine when you are filling it. Clean any
spilled rinse ait with the help of a tissue paper/towel.
• Lid of the rinse aid reservoir is left open. >>> Make sure that the lid of the
rinse aid reservoir is closed after adding rinse aid.
Kitchen utensils are broken.
• Dishes are not placed orderly in the machine. >>> Load the dishes as
described in the user manual.
• Baskets are overloaded. >>> Do not overload the baskets in excess of their
capacity.
Water remains in the dishwasher at the end of the programme.
• Filters are clogged. >>> Check if the filter system is clean. Clean the filter
system regularly as illustrated in section "Cleaning and Care".
• Discharge hose is clogged/blocked. >>> Check the discharge hose. If
necessary, remove the discharge hose, clear the blockage and insert is as
illustrated in the user manual.
CIf you cannot eliminate the problem although you follow the instructions in
this section, consult your dealer or the Authorised Service Agent. Never try to
Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.
Product:
Spelregels forum
Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:
lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;
Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.
Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.
Abonneren
Abonneer u voor het ontvangen van emails voor uw Blomberg smarTouch W20 bij:
nieuwe vragen en antwoorden
nieuwe handleidingen
U ontvangt een email met instructies om u voor één of beide opties in te schrijven.
Ontvang uw handleiding per email
Vul uw emailadres in en ontvang de handleiding van Blomberg smarTouch W20 in de taal/talen: Engels als bijlage per email.
De handleiding is 9,44 mb groot.
U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.
Stel vragen via chat aan uw handleiding
Stel uw vraag over deze PDF
Uw handleiding is per email verstuurd. Controleer uw email
Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.
Er is een email naar u verstuurd om uw inschrijving definitief te maken.
Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken
U heeft geen emailadres opgegeven
Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.
Uw vraag is op deze pagina toegevoegd
Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.
