626843
10
Verklein
Vergroot
Pagina terug
1/19
Pagina verder
1716
4.2 CONNOISSEUR 825™
4.2.1 Installation
Connoisseur 825 Above Counter Installation
Select a location that is near an electrical outlet� Also consider proximity to
ingredients, and patrons as well as available counter space�
Place the blender on the counter in a spot where the air intake vents on the
sides and exhaust on the back of the blender are unobstructed�
Ensure there is enough room above and around the unit to allow for
unhampered movement of the sound enclosure (see Figure 4 for
measurements)�
Plug the unit into an outlet with appropriate electrical protection
Connoisseur 825 In-Counter - Preparation for Installation
Note: You may locate your Blendtec Connoisseur 825 in the same space as
your previous Blendtec in-counter blender. Just remember to ensure proper
spacing for the sound enclosure (see Figure 4 for measurements).
Identify the desired blender location� Consider proximity to ingredients, and patrons
as well as available counter space� Also ensure that an electrical outlet is readily
accessible�
Ensure the location meets all dimensional requirements (see Figures 4 and 5)�
The countertop can be no thicker than ¾” (19 cm)� A thicker countertop will
obstruct motor ventilation�
If installing more than one blender, allow 14”–16” (356 - 406 cm) of center-to-center
blender spacing�
If installing a sound enclosure, allow a clearance of at least 5 ½” (14 cm) from the
sound enclosure to the wall and 26” (66 cm) from the countertop to any over-the-
counter cabinetry�
Ensure lower cabinetry allows adequate airflow�
The blender draws ambient air into the vent holes located on the upper sides
of the motor and then evacuates hot air through the vents on the bottom of the
motor� For the motor to cool properly, a sufficient amount of air must be able to
circulate around the motor�
There should be at least 6 ½” (165 cm of space from the countertop to the next
lower shelf of the cabinet, leaving a minimum space of 3” (76 cm) between
the bottom of the motor and the lower shelf� Cabinetry should not be closed; it
should allow air to flow freely from the outside to the inside of the cabinet space�
Plastic bags, cups, and so forth, should not be stored closer than 3” (76 cm) from
the bottom of the motor�
Cut a hole in the countertop 4 ⅜“ (11�1 cm) wide and 5 ⅞” (14�9 cm) long (see the
countertop hole template in Appendix A)� Ensure that the 4 ⅜” (11�1 cm) sides are
parallel with the machine operator
Note: Double check to ensure that all space requirements and measurements
are correct BEFORE cutting.
SOUND ENCLOSURE
BLADE ASSEMBLY
HARDENED METAL
DRIVE SOCKET & MOTOR
MOTOR BASE
EASY-CLEAN JAR
CONNOISSEUR 825™
COMMERCIAL LINE DRAWINGS >> WILDSIDE+ JAR
Figure 4. Connoisseur 825 Dimensions
18 ½"
(46.8 cm)
22 ½"
(57. 2 cm)
9 ⅜"
(23.6 cm)
9 ⅜"
(23.7 cm)
2 ⅝"
(6.6 cm)
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Blendtec CHEF 600 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Blendtec CHEF 600 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,79 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Blendtec CHEF 600

Blendtec CHEF 600 Gebruiksaanwijzing - English, Français, Espanõl - 156 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info