614191
5
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
GTb 8200 A
5
8 Right loudspeaker input
9 Left loudspeaker input
: Power-on indicator (Power/Protect)
; Automatic switch-on
< Preampli er inputs
Voltage supply
We recommend a minimum cross section of 1.5 mm
2
.
Route commercially available plus cables to the battery
and connect via fuse holder.
Use cable glands for holes with sharp edges.
Securely fasten commercially available minus cables to a
noise-free earth point (chassis screw, chassis metal) (not
to the minus pole of the battery).
Scrap the contact surfaces of the earth point until they
are bright and grease with graphite grease.
Connection
6 is connected to the positive pole of the
battery and connection 4 to negative vehicle ground.
The control of the GTb 8200 A should ideally be a two-
channel control, either via the preampli er outputs or the
loudspeaker outputs of the car sound system. A control
solely via the right or left channel is also possible since the
low-frequency portion of the music is generally identical
on both channels.
Integrated fuse
The fuse integrated in the ampli er protects the output stage
and the entire electrical system in case of a malfunction. If a
replacement fuse is used, never bridge fuses or replace them
with a type with higher current.
Audio inputs
You can select between 2 di erent audio inputs;
Cinch (RCA)
High level (loudspeaker connections)
Use only one of the audio inputs; otherwise, it may lead to
audio interferences.
The preampli er outputs are connected to the cinch (RCA)
sockets
< of the subwoofer box via a shielded sound cable.
With control via the loudspeaker outputs, the input connec-
tions of pos.
8/9 are fed to the closest loudspeaker cables
(front or rear) on the left and right. They are separated and
connected to the input connections. The polarity of the
+ or – connections must be observed. Bridge output stages
(BTL) can also be connected directly without an additional
adapter.
Switching on/o
A special feature of the GTb 8200 A is its automatic switch-on.
It is set via the INPUT switch ;:
RCA
Switching on/off via the car sound system. The remote
connection
5 of the GTb 8200 A must be connected with
a switchable 12-V power supply (e.g. switching output of
the car sound system).
HIGH
Switching on/o via the loudspeaker connections
8/9.
The subwoofer box automatically switches on if a music
signal is received. If no music signal is received for more
than 60 seconds, the GTb 8200 A automatically switches
o .
GAIN control
The GAIN control 3 is used to adjust the input sensitivity of
the power ampli er to the output voltage of your car sound
system preampli er output.
The adjustment range is from 0.3 V to 19 V.
If a car sound system of a third party manufacturer is con-
nected, the input sensitivity must be adjusted corresponding
to the manufacturer data.
A few important explanations in this context:
By turning the control clockwise, the input sensitivity of the
ampli er and, therefore, also the volume increases. However,
this is not a volume control; no further ampli er output
can be achieved in the end position, even if it may sound
like that at the beginning. The system merely increases the
volume faster if the volume control of the car sound system
is turned up.
X-OVER frequency control
The X-OVER control 1 allows setting the desired entry
frequency.
Example:
At a setting of 150 Hz, the ampli er has a frequency range
of 30 Hz to 150 Hz.
Settings
The following control setting is recommended as basic
setting before putting the device into operation: Sensitiv-
ity (GAIN) Pos. 3 to minimum, PHASE Pos. 2 to 0°,  lter
(X-OVER) Pos. 1 to approx. 80 Hz. Switch on the device and
select a musical piece with distinctive bass playback.
Increase the volume of your car sound system to the desired
volume level. Now slowly increase the GAIN control
3 until
you can hear a clear ampli cation of the bass level. Next, use
the X-OVER control 1 to select a  lter setting that provides
a well-contoured bass. You may have to alternately optimise
the sensitivity setting 3 and the  lter setting 1.
A droning bass with excessive volume requires a  lter setting
with a low frequency.
The phase switch
2 must be set so that the bass is inte-
grated into the acoustic pattern as best as possible and not
recognisable as an individual source.
Also check your settings of the GTb 8200 A with the bass
control fully open and, if necessary, with activated loudness.
An overloading of the subwoofer box by selecting an exces-
sive ampli cation (pos.
3) results in a distorted playback and
can damage the loudspeaker.
Power-on indicator
Green LED:
Output stage on, regular operating status.
Red LED:
Output stage is electronically switched o due to an error.
GTb8200A_13LG.indd 5GTb8200A_13LG.indd 5 19.11.2013 10:34:36 Uhr19.11.2013 10:34:36 Uhr
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Blaupunkt GTb 8200 A bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Blaupunkt GTb 8200 A in de taal/talen: Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools als bijlage per email.

De handleiding is 0,56 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info